Gemini CDJ-15 Manual Del Operador página 4

CUE INSTRUCTIONS:
1. To start the play at a point other than the beginning of a track, follow
these instructions:
First choose the track you wish to play, and then press PLAY/PAUSE
(9) so the unit goes into the play mode. Press PLAY/PAUSE (9) to
pause play at the spot where you want the play to start the CUE
POINT. Use the SEARCH BUTTONS (7) to pick the precise spot you
want play to begin, then press PLAY/PAUSE (9) again to save the cue
point. Press the CUE (8) button to pause play at the cue point (the unit
will go into the pause mode and the location indicated on the display
will be the memorized cue point). You can preview the cue point by
pressing and holding down CUE (8). Press PLAY/PAUSE (9) to begin
play from the cue point.
NOTE: AFTER A CUE POINT IS SET, PRESSING THE TRACK SKIP
(6) BUTTONS CLEARS THE CUE POINT. WHEN YOU PRESS THE
CUE (8) BUTTON IN THE NEW TRACK, THE BEGINNING OF
THAT TRACK WILL BE THE NEW CUE POINT.
2. Once you have saved a cue point you can fine tune or change the
memorized cue point:
To change a cue point, push PLAY/PAUSE (9) so the unit plays from
the cue point, then press PLAY/PAUSE (9) at the spot you wish your
new cue point to be. Press PLAY/PAUSE (9) again to save the cue
point. The unit will go into the pause mode and the location indicated on
the display will be the new memorized cue point.
To fine tune a cue point, pause play at the memorized cue point, then
use the SEARCH (7) buttons to scan frame by frame (1/75th of a
second) to where you want play to begin. Press PLAY/PAUSE (9) to
save the new cue point.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT
(TO HELP YOU FIND THE BEAT). THE STUTTERING EFFECT
WILL END WHEN YOU PRESS PLAY/PAUSE (9) TO SAVE THE
CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN
THE SEARCH (7) BUTTON, THE UNIT WILL SCAN QUICKLY
AFTER 10 FRAMES.
TROUBLE SHOOTING:
• If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
• If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
• If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Disc Type................................Standard Compact discs (12 cm & 8 cm)
Time Display.....................Track Elapsed, Track Remain, or Total remain
Variable Pitch......................................± 16% Slider with Resume Switch
Start...........................................................................Within 0.03 seconds
Track Selection.....................................................................1 to 99 Tracks
AUDIO SECTION:
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..........................................................................8 Times
Sampling Frequency.....................................................................44.1 kHz
Frequency Response......................................................20 Hz to 20 kHz
Total Harmonic Distortion..............................................Less Than 0.005%
Signal to Noise Ratio.....................................................................>96 dB
Dynamic Range.................................................................................>94 dB
Output Level (nominal)........................................................1.9 Volts R.M.S.
Power Supply.......................................................AC 120/230V, 60/50 Hz
Dimensions...............................8.38" x 8.86" x 3.75" (213 x 225 x 95 mm)
Weight..................................................................................4.5 lbs. (2 kg)
* Specifications and design are subject to change without notice
for purpose of improvement.
(4)