Using The Saw - EINHELL TC-TS 2025/2 eco Manual De Instrucciones

6.2 Fitting the splitter (Fig. 6)
•
Insert the splitter (5) behind the mounting pla-
te (37) and fasten it with the fastening screw
(19). The mounting plate and screw are alrea-
dy fitted to the machine.
•
The splitter will be in line with the saw blade if
it has been inserted correctly.
6.3 Setting the splitter (Fig. 9,10)
•
Danger! Pull out the power plug.
•
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
•
Remove the saw blade guard (see 6.4).
•
Take out the table insert (6) (see 6.5).
•
Slacken the fixing screw (19).
•
Push up the splitter (5) until the gap between
the saw table (1) and the upper edge of the
splitter (5) equals approx. 10 cm.
•
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
•
Retighten the screw (19) and mount the table
insert (6) (Fig. 8).
6.4 Fitting / removing the saw blade guard
(Fig. 3,7)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Do not tighten the screw (15) too far – the bla-
de guard must be able to move freely.
•
To remove the saw blade guard, proceed in
reverse order.
Warning!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.5 Changing the table insert (Figure 8)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the 1 countersunk head screws (17).
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.6 Fitting/replacing the blade (Fig. 7)
Danger! Unplug the device from the mains
power.
•
Caution! Always wear gloves when changing
and handling the saw blade.
•
Remove the table insert by removing the
Anl_TC_TS_2025_2_ECO_SPK9.indb 25 Anl_TC_TS_2025_2_ECO_SPK9.indb 25
GB
countersunk head screws (see 6.5).
•
Place the wrench (33) on the flange (39)
•
Undo the flange bolt (40) using the wrench
(32) by turning it in the direction of rotation of
the saw blade.
•
Remove the flange (39) and pull off the saw
blade.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Mount and fasten the new saw blade in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter (5) and the saw gu-
ard (2) (see 6.2, 6.3., 6.4.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.

7. Using the saw

7.1. ON/OFF switch (Fig. 1)
•
To turn the saw on, press the green button
"I". Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
•
To turn the machine off again, press the red
button "0".
7.2. Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
7.3. Parallel stop
7.3.1. Stop height (Fig. 11-14)
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
For thick material you must use the stop rail
(23) as shown in Fig. 12, for thin material you
must use the stop rail as shown in Fig.13.
•
To change over the stop rail (23) to the lo-
wer guide face you have to slacken the two
- 25 -
18.12.2017 08:46:53 18.12.2017 08:46:53