Before Starting The Equipment; Assembly - EINHELL TC-TS 2025/2 eco Manual De Instrucciones

Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Operation
L sound pressure level ........................ 91 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 104 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and im-
mission levels it is impossible to draw any certain
conclusions as to the need for additional precau-
tions. Factors with a potential infl uence on the ac-
tual immission level at the workplace include the
duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machi-
nes and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
Anl_TC_TS_2025_2_ECO_SPK9.indb 24 Anl_TC_TS_2025_2_ECO_SPK9.indb 24
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.

6. Assembly

Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Assembling the base frame (Fig. 2, 4-5)
•
Turn the bench-type circular over and set it
down on the floor or suitable surface (work-
bench).
•
Use the hex screws (a) and washers (b) to
fasten the four legs (29) loosely to the saw.
•
Fasten the cross struts (30) to the legs (29)
using the round-head head screws (c),
washers (d), spring washers (e) and and nuts
(f).
•
Fasten the additional legs (36) to the legs
(29) using the hex screws (g), washers (h),
spring washers (e) and and nuts (i).
•
Fit the rubber feet (13) to the legs.
•
Turn the saw over and then tighten all the
screws and nuts.
•
Fasten the holder for the cross stop by
pressing it into the back of the housing (clip
connection)
- 24 -
18.12.2017 08:46:53 18.12.2017 08:46:53