Sunrise Medical Quickie All Court Manual De Instrucciones página 14

E N G L I S H
FIXED BACK– Zero Offset (Fig. C)
1. Remove screws (2 & 2C), nuts (3) and eccentric washer (4) from
backplate / backrest assembly
2. Aluminum– Swap the 1-3/4" long screw (2) for a 1-7/8" long screw
(2A), and the two 1-7/8" long screws (2C) for two 2" long screws
(2D). Swap the step saddle (5) for the small saddle (5A).
Titanium– Swap the 1-7/8" long screw (2) for a 2" long screw (2A),
and the two 1-7/8" long screws (2C) for two 2" long screws (2D).
Swap the step saddle (5) for the small saddle (5A).
3. Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic washer (7), plastic
saddle (5A) and backrest tube.
4. Aluminum– Insert 1-7/8" long screw (2A) through the eccentric
washer (4), backplate (1), plastic washer (7), side guard (6), plastic
saddle (5A) and backrest tube. Attach nut (3).
Titanium– Insert 2" long screw (2A) through the eccentric washer
(4), backplate (1), plastic washer (7), side guard (6), plastic saddle
(5A) and backrest tube. Attach nut (3).
5. Aluminum– Insert 2" long screw (2D) through the backplate (1),
offset plastic saddle (5) and backrest tube. Attach nut (3).
Titanium– Insert 1-7/8" long screw (2B) through the backplate (1),
offset plastic saddle (5) and backrest tube. Attach nut (3).
6. Insert 2" long screws (2D) through the backplate (1), plastic washers
(8), plastic saddles (9) and seat frame tube. Attach nuts (3).
7. Align slot in side guard with hole in seat frame.
8. Insert 1-7/8" long screw (11) through side guard bushing (12), plastic
washer (7), sideguard slot, 2nd plastic washer (7), plastic saddle (5A),
and seat frame. Attach nut (3).
9. Secure screws (2A, 2D & 11 ) and nuts (3).
10. Repeat procedure for opposite side.
Figure C – Fixed Back, Zero Offset
930493 Rev. A
FIXED BACK– 1/4" Offset (Fig. D)
1. Remove screw (2), nut (3) and eccentric washer (4) from backplate /
backrest assembly.
2. Aluminum– Swap the 1-3/4" long screw (2) for a 1-7/8" long screw
(2A).
Titanium– Swap the 1-7/8" long screw (2) for a 2" long screw (2A).
3. Choose the side guard height by aligning one of the holes in the side
guard, with the holes in the backplate (1), plastic saddle offset (5)
and backrest tube.
4. Aluminum– Insert 1-7/8" long screw (2A) through the side guard
(6), plastic washer (7), eccentric washer (4), backplate (1), plastic
saddle offset (5) and backrest tube. Attach nut (3).
Titanium– Insert 2" long screw (2A) through the side guard (6),
plastic washer (7), eccentric washer (4), backplate (1), plastic saddle
offset (5) and backrest tube. Attach nut (3).
5. Align slot in side guard with hole in seat frame.
6. Insert a 2" long screw (8) through side guard bushing (9), plastic
washer (7), sideguard slot, 2 plastic washers (7), plastic saddle offset
(5) and seat frame. Attach nut (3).
7. Secure screws (2A & 8) and nuts (3).
8. Repeat procedure for opposite side.
Figure D – Fixed Back, 1/4" Offset
14
Backrest
Tube
Seat
Frame