Tabla de contenido
Idiomas disponibles
Idiomas disponibles
STACKEDWASHER/DRYER MAINTENANCE INSTRUCTIONS
Washer
Cleaning the Door Seal/Bellow
To clean washer interior:
1. Open the washer
door and remove any clothing
or items from
the washer.
2. Inspect
inner glass door. If debris
is present,
wipe it off using a
damp cloth.
3. Inspect the colored
seal/bellow
between
the door opening
and
the basket for stained
areas. Pull back the seal/bellow
to inspect
all areas under the seal/bellow
and to check for foreign
objects.
J
Seal/Bellow
4. If stained
areas are found, wipe down these areas of the seal/
bellow:
a) Mix a dilute solution,
using 177 mL (3/4 cup) of liquid chlorine
bleach,
and 3.8 L (1 gal.) of warm tap water.
b) Wipe the seal/bellow
area with the dilute solution,
using
a damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly
with a dry cloth and let the
washer
interior air dry with door open.
I M PORTANT:
m Wear rubber gloves when cleaning
for prolonged
periods.
m Refer to the bleach
manufacturer's
instructions
for proper
use.
Maintenance
Instructions:
This washer
has a special cycle that uses higher water volumes
in combination
with Jiquid chlorine
bleach to thoroughly
dean the
inside of the washer.
NOTES:
m Read these instructions completely
before beginning
the
cleaning
process.
m If necessary,
the cleaning
cycle may be interrupted
by pressing
the lower-right
(QUICK
CYCLE)
button
twice. However,
this will
not immediately
stop the cycle. The washer
will continue
with
several rinse and drain steps to ensure that all remaining
bleach
is rinsed from the washer.
1. Open the washer
door and remove
any clothing
or items from
the washer.
2. Use liquid
chlorine
bleach:
Open the dispenser
drawer
and immediately
add
160 mL (2/3 cup) of liquid chlorine
bleach to the bleach
compartment.
NOTE:
Do not add any detergent.
Use of more than 160 mL
(2/3 cup) of bleach
will cause product
damage
over time.
3. Close the washer
door and the dispenser
drawer.
4. To start the Washer
Cleanout
cycle, first enter "Service
Mode_'
Then press and hold the lower-right
(QUICK
CYCLE)
button for
2 seconds.
With the entire display flashing,
press the center-
right (BRIGHTS)
button.
To exit out of the service
mode and activate the dean
wash
cycle, push the BRIGHTS
button,
then turn the key.
NOTE: The door will lock, the basket
will rotate
1/2 turn, then
the door will unlock and lock again, then the Washer
Cleanout
Cycle will continue.
The washer
will not fill, but the basket will rotate while
the washer
runs a short sensing
cycle. This will take
approximately
3 minutes.
5. The cycle will determine
whether
clothing
or other items are in
the washer.
a) If no items are detected
in the washer,
it will proceed
to
Step
7.
b) If any items are detected
in the washer,
"F-34"
will be
displayed.
Then the door will unlock.
m Enter the service
mode and then press and hold the
lower-right
(QUICK
CYCLE)
button
to cancel the failure
code. Then repeat steps 1,3, and 4 to start the cycle
again.
6. Once the cycle has begun,
allow the cycle to complete.
7. After the cycle is complete,
leave the door open slightly
to allow
for better ventilation
and drying of washer
interior.
26
Tabla de contenido
