Saw Blade; Intended Use - Stanley STSC1718 Manual De Instrucciones

Caution! Laceration Hazard. Keep hands away from
cutting areas. Keep hands away from blades. Never place
hands in front of or behind the path of the blade while cutting.
Do not reach underneath work while blade is rotating. Do not
attempt to remove cut material when blade is moving.
f Support large panels. Large panels must be
supported as shown (Fig. A) in this manual to minimize
the risk of blade pinching and kickback. Material
supported only at the ends (Fig. B) will lead to blade
pinching. When cutting operation requires the resting
of the saw on the workpiece, the saw shall be rested
on the larger portion and the smaller piece cut off.
f Use only correct blades and blade assembly
components when mounting blades. Do not use
blades with incorrect size holes. Never use defective
or incorrect blade washers or bolts. Follow blade
assembly procedures.
f Adjustments. Before cutting be sure depth and bevel
adjustments are tight.
f Support and secure the work properly. Insure
that the material to be cut is clamped (Fig. C), and
solidly supported and balanced on a strong, stable
and level work surface. Support the work so that
the wide portion of the saw shoe is on the portion of
the material that doesn't fall after the cut is made.
Never hold cut off piece by hand (Fig. D). Kickback
from blade pinch can result. Keep both hands on saw
at all times.
f Stay alert and exercise control. Keep body
positioned to one side of blade. Always maintain
a firm grip and control of saw with both hands.
Do not change hand grip or body position while saw
is running. Take precaution to avoid injury from cut off
pieces and other falling material during operation.
Danger! Release switch immediately if blade binds
or saw stalls.
FEATURES (Fig. E)
This tool includes some or all of the following features.
1. On/Off Switch
2. Main Handle
3. Secondary Handle
4. Shoe

5. Saw Blade

6. Saw Blade Guard
7. Blade Guard Retracting Lever
8. Saw Blade Spanner Wrench
9. Bevel Adjustment Knob
10. Outer Washer
11. Blade Retaining Screw
Saw Blade Hex Wrench (Shown on Fig.I)
18. Rip Fence (Shown on Fig. M)
Inner Flange (Shown on Fig. J)

INTENDED USE

Your Stanley saw has been designed for sawing wood and
wood products. This tool is intended for consumer use only
f For tools intended to cut wood, instruction on correct
use of the dust collection system.
f For tools intended to cut wood, instruction to wear a
dust mask.
f Instrcution to only use saw blades recommended.
f Instruction to always wear hearing protection.
ASSEMBLY/ADJUSTMENT SET-UP
Warning! Always unplug saw from power supply before
any of the following operations.
Adjusting the depth of cut (Fig. F and G)
The depth of cut should be set according to the thickness
of the workpiece.
f Loosen the lever (12) to unlock the saw shoe.
f Move the saw shoe (4) into the desired position.
The corresponding depth of cut can be read
from the scale (13).
f Tighten the lever to lock the saw shoe in place.
f Set depth adjustment of saw such that one tooth of the
blade projects below the workpiece as shown in Fig. G.
Adjusting the bevel angle (Fig. H)
This tool can be set to bevel angles between 0° and 45°
f Loosen the locking knob (9) to unlock the saw shoe.
f Move the saw shoe (4) into the desired position.
The corresponding bevel angle can be read
from the scale (14).
f Tighten the locking knob to lock the saw shoe in place.
Attaching the blade (Fig. I and J)
f To prevent spindle rotation engage the protrusions
of the spanner wrench (8) into the holes in the
outer washer (10) as shown in Fig. I.
f Loosen and remove the blade retaining screw (11) by
turning the hex wrench (15) counter- clockwise.
f Remove the outer washer.
f Check and re-assembly inner flange (20) on spindle
(16). Insure the correct side of inner flange (20) faces
outward and match saw blade with diameter arbor well.
f Place the saw blade (5) onto the inner flange (20),
making sure that the arrow on the blade points in the
same direction as the arrow on the tool.
f Fit the outer washer (10) on the spindle.
f Insert the blade retaining screw (11) into the hole in
the spindle.
f Prevent spindle rotation by engaging the spanne
wrench into the holes of the outer washer.
f Securely tighten the blade retaining screw by
holding the spanner wrench and turning hex wrench
clockwise to tighten the blade retaining screw.
ENGLISH • 21