Basic Adjustments - IMG STAGELINE LED-500DX/WS Manual De Instrucciones

2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the unit is to be put out of operation defini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
3 Applications
The stroboscope is suited for applications on stage, in
discotheques or party rooms. As a light source, it has
192 super bright LEDs with a low power consumption
and a long life.
The stroboscope is designed for control via a DMX
light controller (1 DMX control channel); however, it
can also be operated on its own or with the remote con-
trol LC-3 available as an accessory.
4 Mounting
G
Always place the unit in such a way that a sufficient
air circulation will be ensured during operation.
Never cover the air vents on the housing (e. g. by
curtains).
G
The minimum distance to the illuminated object
should be 10 cm.
1) For wall mounting, a support (3) is provided on the
rear side of the unit. At a suitable place, screw four
matching screws or screw hooks into the wall at the
correct distance; then hang up the stroboscope via
the screws.
2) For suspended mounting of the unit at a cross bar
or a lighting stand, screw the mounting bracket pro-
vided (1) to the support (3), as illustrated in fig. 1.
Screw the mounting bracket with the unit to the
cross bar or to the lighting stand.
WARNING Mount the stroboscope safely and
expertly. If it is installed at a place
where people may walk or sit under
it, additionally secure it (e. g. by a
safety rope; fasten the safety rope in
such a way that, even in the event of
a fall, the maximum falling distance
of the light effect unit will not exceed
20 cm).
3) To align the stroboscope, release the locking
screws (2). Adjust the desired inclination of the unit,
then fasten the screws again.
5 Setting the Stroboscope into Operation
WARNING Never look directly into the LEDs; this
may cause eye damage.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
Connect the mains cable provided to the mains jack (4)
first, then connect it to a socket (230 V/50 Hz). All
LEDs will flash a few times and the display (6) will
show . Then the unit will be ready for operation
and can be controlled via a DMX controller (
ter 7). However, it can also be controlled via the micro-
phone (15) [ chapter 6.1.1] or manually [
6.1.2]. To switch off the unit, disconnect the mains
plug.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket which is
switched on and off via a light switch.
Caution: Do not connect the unit to the mains voltage
via a dimmer!

5.1 Basic adjustments

The following basic adjustments can be made via the
display (6) and the control buttons (9 – 11). For this
purpose, press the button MENU (9) so many times
until the desired function is displayed. Then press the
button ENTER (11). Make sure that the next button is
pressed within 10 seconds, otherwise the adjusting
process will end. The menu structure can be found on
page 15.
Operating mode MASTER or SLAVE
Use the button or (10) to select:
The operating mode MASTER must be
selected for operation without a DMX controller
when the unit is used on its own or used as a
master unit to control further slave units.
The operating mode SLAVE 1 must be
selected when the unit is used as a slave unit
to be controlled in sync with the master unit
( chapter 6.2).
The operating mode SLAVE 2 must be se-
lected when the unit is used as a slave unit to
be controlled by the master unit, but its strobo-
scope effects are to be opposite to those of the
master unit.
To memorize, press the button ENTER (11).
Blackout mode on or off
Use the button
or
(10) to select:
The LEDs will flash or be permanently on. This
adjustment must be selected when the unit is
operated without a DMX controller.
The LEDs will only flash or light up when there
is a DMX control signal at the jack DMX INPUT
GB
chap-
chapter
11