Idiomas disponibles
Idiomas disponibles
EN
chainsaw is in contact with no objects.
Never operate the device without the
front cut protection. Risk of injury!
Switching on
1. Place the battery (14) into the device
2. Check the load status of the rechargeable bat-
tery before starting.
3. Hold the device firmly with both hands, with
your right hand on the handle (5) and left hand
on the grip (2). Your thumb and fingers must
tightly clasp the handle (5). Never use the
device onehanded. Risk of injury!
4. To turn on, press the switch lock (3) with your
thumb or index finger and then press the on/
off switch (4); the device will run at maximum
speed. Release the switch lock (3).
5. The device will switch off again when you
release the on/off switch (4). The device cannot
be switched to continuous operation.
Changing the blade bar
1. Switch off the device and remove the battery
(14) from the device.
2. Place the device on a level surface.
3. Turn the mounting knob (10) of the sprocket
cover in a counter-clockwise direction in order
to loosen the chain tension and to remove the
sprocket cover (9).
4. Remove the blade bar (11) and saw chain (12).
To disassemble, hold the blade bar (11) tilted
upwards at an angle of approx. 45 degrees in
order to be able to remove the saw chain (12)
more easily from the chain sprocket (17).
5. Replace the blade bar and install the blade bar
and saw chain as described under "Installing
the saw chain and blade bar".
The tensioning of the saw chain is described in the
"Assembly" section.
SAWING TECHNIqUES
General information
Observe noise protection rules and other
local regulations when working with the
tool. Local regulations may require a
suitability test.
• Dirt, stones, loose bark, nails, clips and wires
must be removed from the tree.
• Always stand above the tree trunk when sawing
12
on slopes.
• To keep total control while sawing through, re-
duce the pressure at the end of the cut without
loosening your grip on the handles of the pruner
saw. Make sure the saw chain does not touch
the ground. After finishing the cut, wait until the
pruner saw comes to a stop before removing it.
• Always switch off the motor of the pruner saw
before changing between trees.
• You will have better control over the device if
you saw using the lower edge of the blade bar
(chain in pulling direction).
• The saw chain must not touch the ground or
any object while sawing through the material or
thereafter.
• Ensure that the saw chain does not get stuck
while sawing. The log must not break or splinter.
• Please also observe the precautionary measu-
res to protect against kickback (see the safety
information).
• For sawing work on hillsides, always stand in
the area above the log. To keep total control
while sawing through, reduce the pressure at
the end of the cut without loosening your grip
on the handles of the pruner saw. Make sure
the saw chain does not touch the ground. After
finishing the cut, wait until the saw chain co-
mes to a stop before removing it. Always switch
off the motor of the pruner saw before changing
between trees.
If the saw chain gets stuck, do not
attempt to pull out the device with force.
There is a risk of injury. Turn the motor off
and use a lever arm or wedge to release
the device.
Cut to length
Cutting to length means sawing felled tree trunks
into small sections. Ensure that you have secure
footing and balance your body weight evenly on
both feet. If possible, the trunk should be protected
and supported by branches, logs or wedges.
• Make sure that the saw chain does not touch
the ground when sawing.
• Make sure you have good footing and stand
above the trunk on sloping terrain. To keep
total control while sawing through, reduce the
pressure at the end of the cut without loosening
your grip on the handles of the pruner saw.
After finishing the cut, wait until the saw chain
www.vonroc.com
