Idiomas disponibles
Idiomas disponibles
˜ LED work light
This product is equipped with a LED work light
the immediate working area to improve visibility in poorly lit
areas.
The LED work light
lights up automatically as soon as
[
]
the product is switched on.
NOTE
The LED work light
u
[
]
approx. 10 seconds after switching off the product.
˜ Working instructions
Torque
Smaller screws/bits can be damaged if you set the torque
or rotational speed too high.
Hard screw joints (in metal)
Particularly high torque occurs, for example in metal screw
joints made using drive sockets. Select a low rotational
speed.
Soft screw joints (e.g. in soft wood)
Again, use a low rotational speed, e.g. to avoid damaging
the surface of the wood upon contact with the screw head.
Use a countersink.
Drilling in wood, metal and other materials
Use a high speed for drill bits with small diameter and a
low speed for drill bits with large diameter.
Select a low speed for hard materials and a high speed for
soft materials.
Secure or fasten the workpiece in a clamp or vice (if
possible).
Mark the spot where you want to drill using a centre punch
or nail. Select a low rotational speed when starting.
Pull the rotating drill bit from the hole repeatedly to remove
dust and chips and clear the hole.
Drilling in metal
Use a metal drill (HSS). For optimum results, cool the
drill bit with cooling lubricant (cutting oil). Metal drill bits
can also be used to drill into plastics. Start with a 3 mm
diameter drill bit and then increase the size until the desired
hole diameter is achieved.
Drilling in wood
Use a wood drill with a lathe centre.
Deep holes: Use an auger bit.
Large-diameter holes: Use a Forstner bit.
Small screws can be screwed directly into soft wood.
to illuminate
[
]
stays on for an additional
Belt clip
(Fig. J)
m
CAUTION! RISK OF INJURY!
Before hanging the product in the belt: Push the rotation
u
direction switch
to the centre position (lock).
[
5 ]
This prevents the product from being switched on
accidentally.
NOTE
The belt clip
allows the tool to be hooked on belt
u
[
9 ]
or pocket.
The belt clip is not assembled upon delivery.
u
The belt clip can be mounted on either side of a belt.
u
For the assembly of the belt clip a cross tip screwdriver
u
is required.
1.
Use a cross tip screwdriver to loosen the screw of the belt
clip
.
9 ]
[
2.
Insert the belt clip on either side of the product.
3.
Use a cross tip screwdriver to tighten the screw.
˜ Connecting the product to the
PARKSIDE app
˜ Activate/deactivate the Bluetooth
function on the battery
1.
Press and hold the
for 3 seconds to activate the Bluetooth
orange LED of the charging level LEDs
Bluetooth
function is enabled.
®
2.
Release the
button
3.
Press and hold the
for 10 seconds to deactivate the Bluetooth
orange LED of the charging level LEDs
function is deactivated. In the PARKSIDE app
Bluetooth
®
the product is shown as offline.
˜ Connecting the product to the
PARKSIDE app
NOTE
The product can only be connected to the PARKSIDE
u
app if the battery pack
Only Smart Performance rechargeable batteries can be
u
connected to the PARKSIDE app.
1.
Press and hold the
for 3 seconds to activate the Bluetooth
2.
Enable the Bluetooth
function on your smartphone.
®
Open the PARKSIDE app.
3.
®
button
on the battery pack
[
]
function. The
®
lights up. The
[
]
.
[
]
button
on the battery pack
[
]
function. The
®
goes off. The
[
]
is inserted in the product.
[
]
button
on the battery pack
[
]
function.
®
GB/IE
[
]
[
]
[
]
35
