Manoeuvring The Caravan - Truma Mover S Instrucciones De Uso

Manoeuvring the caravan

Please read the „Safety-related instructions" before
using the Mover!
Apply handbrake with caravan uncoupled.
Unplug 13-pin plug from vehicle and plug into safety socket of
caravan.
For safety reasons the Mover can only be operated if the
13-pin plug of the caravan has been plugged into the
safety socket.
If there is a fault in both caravan brake lights, the power
circuit of the safety socket is not closed. In this case the
Mover cannot be operated.
Switch remote hand set on – green LED flashes for 5 seconds
in combination with the acoustic alarm until the control unit is
ready for operation.
Simultaneously press the two buttons (h) for swivelling in,
which starts after approx. 3 seconds (safety delay).
Use the position indicator to check whether both drive
rollers have been correctly applied (arrow of yellow position
indicator is above the line that is closest to the tyre).
Before operating the Mover, release the handbrake.
The six direction buttons provide movement in six directions –
forward, reverse, left forward, left reverse, right forward,
right reverse.
With the Mover SE, the „left forward" (e) and „right reverse" (f)
or „right forward" (d) and „left reverse" (g) buttons can also be
pressed simultaneously in order to turn the caravan in a circle
on the spot without moving it forwards.
The soft start/stop facility means that the caravan starts
without jerking and is gently braked when stopping.
If the buttons are released or the radio signal is interfered with
or becomes too weak, the caravan stops. Your Mover cannot
be activated by radio devices or other Mover remote hand sets.
After starting up, the Mover moves at one speed only. The
speed will increase a little when going downhill and decrease a
little when going uphill.
After manoeuvring, first apply the handbrake and then
swivel the drive rollers away from the tyres.
Move slide switch on remote control to the „Off"
switch the remote control and the Mover off.
The slide switch also acts as an „Emergency stop"
switch.
When manoeuvring is complete or if the system is going to be
idle for long periods, unplug the plug from the safety socket.
Hitching to a tow car
1. It is totally possible to position the caravan's hitch to a
stationary car tow ball using the Mover, but take some care.
2. Use the instructions above as your guide. Use the button
controls to bring the caravan to the car (car handbrake „ON",
and car in gear). Use a button stabbing technique to exactly
position the hitch directly over the ball. Lower the hitch to the
ball and engage in the normal way using the jockey wheel.
3. Prepare the caravan for towing as usual. The caravan must
not be towed with the drive rollers swivelled in.
Maintenance
1. Please do not allow the drive units to become soiled with
coarse road material. When you are cleaning the caravan,
spray the Mover with a water hose to dissolve mud etc. Please
ensure that no stones, twigs or the like become trapped in the
equipment. The control unit does not require maintenance.
Please keep the remote hand set in a dry place.
2. Every year (and/or before putting away for the winter), clean
Mover as described, dry and lightly spray the drive unit guides
with oil spray or a similar water-repelling lubricant. Do not put
lubricant on the rollers or the tyres! Swivel the drive units
in and out several times to allow the lubricant to penetrate all
the guides. Do not park the caravan with the drive rollers
swivelled in.
3. To prevent the battery from becoming totally discharged
during long periods of inactivity it must be disconnected and
recharged before using again. Charge the caravan battery
before starting up.
It is extremely easy for you or your caravan dealer to perform
the checking and maintenance of your Mover during the an-
nual inspection of your caravan. If in doubt, please contact the
Truma-Services (page 73).
Checks
l
Check the installation, wiring and connections for damage
at regular intervals. The drive units must be able to move
freely and be returned automatically to the safe idle position
when they are swivelled out. If this is not the case, examine
drive units for soiling or corrosion at the guides and clean if
necessary. Undo all moving parts as required and oil or spray
with a lubricant such as WD40 to ensure that the equipment
moves correctly and provides the full range of movement.
£
l
position to After the annual inspection, check whether all motors react
properly to the buttons on the remote control.
Emergency swivelling out function
If the caravan battery has become so discharged that swivel-
ling out cannot be performed using electrical means, or a fault
has occurred, the drive motors can be swivelled out manually.
Once the battery has been recharged the rollers can be
swivelled in again electrically.
Prise out the plastic cap (m) at the rear
end of the swivel-in motor using a screw-
driver. Place the socket wrench (size 7 –
included in scope of delivery) onto the
hexagon bolt and swivel the drive unit
m
out by turning anticlockwise. Repeat
procedure at the opposite side.
15