Metabo AS 36-18 L 20 PC Manual Original página 20

en ENGLISH
38 Air inlet
39 Button for filter cleaning 'PressClean' (PC)
40 CordlessControl transmitter**
* not in scope of delivery
**equipment-specific
8. Initial Operation
Prior to use, check that you are using a
battery pack suitable for the device.
8.1 Battery pack
Charge the battery pack (19) before use.
Recharge the battery pack if performance
diminishes.
The ideal storage temperature is between 10°C and
30°C.
8.2 Removing and inserting the battery pack
Remove: Press the battery pack release button (18)
and remove the battery pack (19) .
To insert: Slide the battery pack (19) in until it
engages.
- recommended capacity 8.0 Ah and greater. The
use of battery packs with a smaller capacity (Ah)
reduces the service life but not the suction power.
- We recommend the use of battery packs with
identical item number.
- The use of battery packs with different capacity
(Ah) is permitted. In this case, the battery pack with
the smaller capacity (Ah) determines the useful life.
8.3 Use a fleece filter bag 635424000 (26)
(see fig. C S. 2)
We recommend using fleece filter bags for:
- Applications, where small amounts of fine dust are
created (e.g. spot-grinding and grinding of paint
and lacquer coatings, extraction of drilling
applications with small diameters < 10 mm of
short duration, etc.).
- Use of machines, such as: routers, planers, small
grinding machines, etc.
When using a fleece bag the filter cleaning is non-
functional.
switch machine OFF; Remove the battery packs.
Open the snap locks (15). Remove the upper part
(9) of the device from the container (2).
See illustration C, page 2. Insert a new fleece filter
bag in the fixture (25) provided.
Replace the upper part of the device on the
container, close the snap locks.
8.4 Use a PE disposal bag 635425000/
635426000 (27) (see fig. C S. 2)
We recommend the use of PE-disposal bags for:
- Applications, where larger amounts of dust are
created (e.g. removal of plaster surfaces, spot-
grinding and grinding of screeds, etc.).
20
- Use of machines, such as e.g.: renovation milling
machines, renovation grinders, drywall grinders,
wall grinders etc.
switch machine OFF; Remove the battery packs.
Open the snap locks (15). Remove the upper part
(9) of the device from the container (2).
Spread out the PE disposal bag (27) evenly across
the container floor. The round holes of the bag must
be on the inside of the container. Arrange the edges
of the PE disposal bag around the container rim so
that the PE disposal bag is firmly clamped on all
sides by the upper part (9) once replaced. The
marking line on the bag must be positioned on the
edge of the container (see fig. C p. 2).
Replace the upper part of the device on the
container, close the snap locks.
8.5 Use a special filter bag H-class
635427000 (28) (see fig. C S. 2)
The special filter bag must be used in the case of
harmful dust.
switch machine OFF; Remove the battery packs.
Open the snap locks (15). Remove the upper part
(9) of the device from the container (2).
Spread out the PE disposal bag evenly across the
container floor. Arrange the edges of the PE filter
bag around the container rim so that the PE bag is
firmly clamped on all sides by the attached upper
part (9). The round holes of the bag must be on the
inside of the container. The marking line on the bag
must be positioned on the edge of the container
(see fig. C p. 2).
Insert the fleece inner bag glued to the PE outer bag
into the fixture (25) provided.
Replace the upper part on the container and close
the snap locks
8.6 Mount accessory fixtures for nozzles and
hose (29)
Fix accessory fixture (29) with enclosed screws and
suitable tools to the device as sown in fig. D p. 2.
8.7 Installing the suction hose
Plug the rear end of the suction hose (23) into the suction opening (4).
8.8 Removing and attaching the connecting
sleeve (36)
Fitting see p. 2 fig. F:
Removal:
Loosen the fitted connecting sleeve (36) by turning
against the hose fixture (fig. F no. 2).
Attaching:
Insert the front hose end (24) with the quick-release
catch into the sleeve until the catch engages.
8.9 Regulating the suction power
By turning the auxiliary air slide (37) the air supply
on the air intake (38) and thus the suction power can
be regulated.