Idiomas disponibles
Idiomas disponibles
ENGLISH
Changing the programme
Important
An ongoing cycle can only be modified if it has been running for a short time. Otherwise, the
detergent may have already been released and the machine has already drained the wash
water. In this case, the detergent dispenser must be refilled (see section "Refilling detergent").
1.
Press the power icon to cancel the programme.
2.
Switch on the dishwasher again and restart a new washing cycle (see section "Starting a
washing cycle") or press the programme icon to change the programme.
Note
If you open the door during the washing cycle, the appliance will stop and beep. Moreover, the
display will show E1 and flash. After closing the door, the appliance will continue to operate
after 10 seconds.
Introducing tableware during the cycle
You can add tableware at any time before the detergent dispenser is activated.
1.
Open the door slightly to stop the dishwasher.
2.
When the spray arms have stopped, you can open it completely. Open the door carefully.
When opening the door, steam may come out.
Add the tableware you forgot.
3.
4.
Close the door and the dishwasher will start after ten seconds.
Warning!
It is dangerous to open the door while washing, as hot water can cause burns.
Switching off the dishwasher
The digital display shows "---"; only in this case the programme is finished.
Switch off the dishwasher by pressing the power icon.
1.
2.
Close the water supply.
Unloading the dishwasher
-
Hot dishes are sensitive to shocks. Therefore, you should let the dishes cool down for 15
minutes before removing them from the appliance.
-
Open the dishwasher door, leave it ajar and wait some minutes before removing the
dishes. This will make them cooler and facilitate the drying process.
-
It is normal for the dishwasher to be damp inside.
-
First empty the lower basket and then the upper one. This will prevent water from the
upper basket from dripping onto the dishes in the lower basket.
78
Bolero Aguazero 6500 C/ Inox C/ Dark C
7. CLEANING AND MAINTENANCE
Filtering system
-
The filter is used to prevent large debris and other debris from entering the pump. Debris
can clog the filter at any time.
-
The filter system consists of a coarse filter, a flat filter (main filter) and a microfilter (fine
filter). Fig. 15
1.
Flat filter
Food and debris will be trapped by a special jet in the lower spray arm.
2.
Coarse filter
-
Large debris, such as bones and glass, which could clog the drain, will be trapped in the
coarse filter.
-
To remove an object caught in this filter, gently squeeze the tabs above this filter and lift
it out.
Microfilter
3.
-
This filter retains dirt and food debris in the drain area and prevents it from being
deposited back into the dishes during a cycle.
-
Check the filters for blockages every time the dishwasher is used.
-
The filter system can be removed by unscrewing the coarse filter. Remove food debris
and clean the filters under running water.
Removing the filtering system Fig. 16
-
Step 1: counterrotate the coarse filter and then lift it up.
-
Step 2: lift the flat filter.
Note
-
To assemble the filtering system, follow the process in reverse.
-
For best performance and results, it is necessary to clean the filtering system. The filter
effectively removes food particles from the wash water, allowing it to recirculate during
the cycle.
-
For this reason, it is advisable to remove larger food particles trapped in the filter after
each wash cycle. Rinse the semi-circular filter under the tap. To remove all filters, pull the
filter handle upwards.
-
Filters should be cleaned at least once a week. To clean the coarse filter and the microfilter,
use a soft cleaning brush. Then, reassemble the filter parts as shown in the figures 15 and
16 and put the whole assembly back into the dishwasher.
-
Put the filter assembly in place and press down. Never use the dishwasher without the
filters installed.
ENGLISH
79
Bolero Aguazero 6500 C/ Inox C/ Dark C
