Tractel Blocfor Manual De Instalación, De Utilización Y De Mantenimiento página 16

• To use a work winch, Scafor
is not complete, if it has been dismantled beforehand
or if components have been replaced by any person
unauthorised by Tractel
EN
• To use the device if a rescue plan has not been put in
place beforehand in the event of a fall by the operator;
• To install a Tractel
structure with a mechanical breaking strength below
16 kN vertically and horizontally. This load may
be applied vertically with a maximum lever arm of
700 mm; and
• To simultaneously use the PPE anchor point at the
end of the jib with an equipped bracket.
8. Associated equipment
8.1. Harness
Meets or exceeds standards and requirements
established by CSA Z259.10-18, ANSI Z359.1-07, ANSI
Z359.11-14, ANSI A10.32-12, OSHA 1926
8.2. Work Winch
Applicable standards
Manufactured in accordance with ANSI, OSHA and
CSA requirements.
8.3. Blocfor
Applicable standards ANSI Z359.1-1999, OSHA 1926,
CSA Z259.2.3-04, type 3
8.4. Scafor
UL classified for man lifting
8.5. Forged steel snap hooks
All snap hooks are proof-loaded 100% at 3,600 lbs.
(16 kN) Gate strength: 3,600 lbs. (16 kN) All carabiners
meet ANSI Z359.12-2009 and CSA Z259.12-11
8.6. Carabiners:
All carabiners are proof-loaded 100% at 3,600 lbs. (16
kN) All carabiners meet ANSI Z359.12-2009 and CSA
Z259.12-11
8.7. Davitrac™+ and Davitrac™
Meets or exceeds standards and requirements
established by ANSI Z359.1-2007, ANSI A10.14 OSHA
1926 CSA fall protection requirements
9. Transport and storage
For associated systems, see the specific manuals of
the associated products.
During storage and/or transport, the product must be:
• Stored at a temperature between -31°F to 140°F
(-35°C and 60°C) and
16
All manuals and user guides at all-guidesbox.com
or Blocfor winch, if it
® ®
.
®
fall-arrest anchor device on a
®
• Protected from chemical, mechanical or any other
type of attack.
10. Equipment compliance
Meets or exceeds standards and requirements
established by ANSI Z359.1-2007, ANSI A10.14 OSHA
1926 CSA fall protection requirements.
11. Marking
The product marking described in this manual indicates:
a. Trade name: Tractel
b. Product description,
c. Applicable standard
d. Product part number
f. Date of manufacturing (YY/MM),
g. Serial number,
h. Pictogram showing that the manual must be
read before use,
o. Minimum breaking strength of the anchor
device,
p. Number of individuals: 3 operators maximum,
w. Safe working load for fall arrest application,
aa. Date of the next periodic inspection,
12. Periodic inspection and repair
An annual periodic inspection is mandatory; however,
depending on the frequency of use, environmental
conditions and regulations of the company or the country
of use, periodic inspections may be more frequent.
WARNING
All equipment must be inspected visually by the
user before each use and at least once a year by
a competent person. If equipment inspection fails, it
must be removed from service and clearly marked
"DO NOT USE". It must then be destroyed or as
per company policy. If any damage or questionable
conditions that are not described below are apparent,
remove the item from service immediately, replace it
and call Tractel for advice.
®
Failure to remove equipment that has been damaged
or has questionable condition could lead to serious
or fatal injury. A detailed record of inspection should
be maintained.
,
®