Idiomas disponibles
Idiomas disponibles
BASIC DRILL PRESS OPERATION
WARNING
!
To avoid possible injury, keep guard closed and in place
while tool is in operation.
To avoid injury from an accidental start, ALWAYS make
sure the switch is in the "OFF" position, the switch key
is removed, and the plug is not connected to the power
source outlet before making belt adjustments.
SPEEDS AND BELT PLACEMENT (FIG. R)
The drill press has 12 speeds, see the chart in Fig. R to
select the correct belt placement for your project.
Fig. R
300 RPM
RPM
560
RPM
990
1
900
RPM
DRILLING SPEED TABLE (RPM)-FOR 15 IN. (381MM) DRILL PRESS
Drill Dim.
Inches
Wood
Aluminum
(mm)
1/32
(0.7 mm)
1/16
(2.5 mm)
3100
1/8
(3.18 mm)
3/16
3100
(4.8 mm)
1/4
(6.4 mm)
1620-2620 1620-2620
5/16
(7.9 mm)
3/8
(9.5 mm)
990-1550
7/16
(11.1 mm)
1/2
(12.7 mm)
1620-2620
9/16
640-700
(14.3 mm)
5/8
(15.9 mm)
OPERATION
390
RPM
450
RPM
640
RPM
700
RPM
1
550
RPM
1
620
RPM
RPM
2
620
RPM
3
100
Material
Plastic
Mild Steel
Stainless
3100
1620-2620
3100
1620-2620 990-1550
990-1550
640-700
640-700
390-560
990-1550
390-560
640-700
ON / OFF SWITCH PANEL (FIG. S)
The "ON / OFF" switch has a removable, safety key.
With the key removed from the switch, unauthorized and
hazardous use by children and others is minimized.
1. To turn the drill press "ON," insert the key (2) into the
slot of the switch (1), and move the switch upward to
the "ON" position.
2. To turn the drill press "OFF," move the switch
downward.
3. To lock the switch in the OFF position, grasp the
sides of the safety switch key, and pull it out.
4. With the switch key removed, the switch will not
operate to power the drill press on.
5. If the switch key is removed while the drill press
is running, it can be turned "OFF" but cannot be
restarted without inserting the switch key.
6. To turn the laser "ON," press the rocker switch (3) to
the on position.
7. Never leave the drill press unattended. Turn the laser
switch and power switch OFF" and wait until it comes
to a complete stop, and remove the safety key to
prevent unauthorized starts.
WARNING
!
ALWAYS lock the switch "OFF" when the drill press
is not in use. Remove the key and keep it in a safe
place. In the event of a power failure, blown fuse,
or tripped circuit breaker, turn the switch "OFF" and
remove the key, preventing an accidental startup
when power comes on.
Fig. S
3100
INSTALLING A DRILL BIT IN THE CHUCK (FIG. T)
1. With the switch "OFF" and the safety key removed,
open the chuck jaws (1) using the chuck key (2). Turn
the chuck key counterclockwise to open the chuck
jaws (1).
2. Insert the drill bit (3) into the chuck far enough to
obtain maximum gripping by the jaws, but not far
enough to touch the spiral grooves (flutes) of the drill
bit when the jaws are tightened.
3. Make sure that the drill is centered in the chuck.
4. Turn the chuck key clockwise to tighten the jaws.
300
WARNING
!
To avoid injury or accident by the chuck key ejecting
forcibly from the chuck when the power is turned
17
3
2
1
