Idiomas disponibles
Idiomas disponibles
PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (21)
will automatically raise the pitch up to +4% or lower the pitch down to
-4% from the existing pitch setting. Releasing the buttons will return the
pitch to the original pitch setting. You can use this function to match the
pitch bend when mixing from one song to another.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (22)
up or down will lower or raise the pitch percentage.
OPERATING INSTRUCTIONS:
1. Press the EJECT (7) button, place a CD in the DISC TRAY (6) and close
the tray door. The display will initially show the number of tracks and the
total time of the CD.
2. Push the TRACK SKIP (13) buttons to select the track you want to play.
3. Press the PLAY/PAUSE (8) button and the unit will instantly play.
CUE INSTRUCTIONS:
1. To start the play at a point other than the beginning of a track, follow
these instructions:
First choose the track you wish to play, and then press PLAY/PAUSE (8)
so the unit goes into the play mode. Press PLAY/PAUSE (8) to pause
play at the spot where you want the play to start the CUE POINT. Use
the SEARCH BUTTONS (14) to pick the precise spot you want play to
begin, then press PLAY/PAUSE (8) again to save the cue point. Press
the CUE (10) button to pause play at the cue point (the unit will go into the
pause mode and the location indicated on the display will be the
memorized cue point). You can preview the cue point by pressing and
holding down CUE (10). Press PLAY/PAUSE (8) to begin play from the
cue point.
2. Once you have saved a cue point you can fine tune or change the
memorized cue point:
To change a cue point, push PLAY/PAUSE (8) so the unit plays from the
cue point, then press PLAY/PAUSE (8) at the spot you wish your new
cue point to be. Press PLAY/PAUSE (8) again to save the cue point. The
unit will go into the pause mode and the location indicated on the display
will be the new memorized cue point.
To fine tune a cue point, pause play at the memorized cue point, then
use the SEARCH (14) buttons to scan frame by frame (1/75th of a
second) to where you want play to begin. Press PLAY/PAUSE (8) to
save the new cue point.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT (TO HELP YOU FIND THE
BEAT). THE STUTTERING EFFECT WILL END WHEN YOU PRESS PLAY/PAUSE (8) TO SAVE
THE CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN THE SEARCH (14)
BUTTON, THE UNIT WILL SCAN QUICKLY AFTER 10 FRAMES.
TROUBLESHOOTING:
• If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
• If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
• If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Disc Type................................Standard Compact discs (12 cm & 8 cm)
Time Display.....................Track Elapsed, Track Remain, or Total remain
Variable Pitch......................................± 16% Slider with Resume Switch
Start...........................................................................Within 0.03 seconds
Track Selection.....................................................................1 to 99 Tracks
AUDIO SECTION:
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..........................................................................8 Times
Sampling Frequency.....................................................................44.1 kHz
Frequency Response......................................................20 Hz to 20 kHz
Total Harmonic Distortion..............................................Less Than 0.005%
Signal to Noise Ratio.....................................................................>96 dB
Dynamic Range.................................................................................>94 dB
Output Level (nominal)........................................................1.9 Volts R.M.S.
Power Supply.......................................................AC 120/230V, 60/50 Hz
Dimensions...............................8.5" x 3.75" x 12.5" (216 x 3.75 x 317 mm)
Weight..................................................................................4.5 lbs. (2 kg)
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
(5)
(5)
(5)
(5)
(5)
