Makita DUX60ZM4 Manual De Instrucciones página 12

Speed adjusting
You can adjust the tool speed by tapping the main
power button.
Each time you tap the main power button, the level of
speed will change.
► Fig.6: 1. Main power button
Indicator
Reverse button for debris removal
WARNING:
Switch off the tool and remove
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch off and
remove the battery cartridge may result in serious personal injury from accidental start-up.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris entan-
gled in the tool.
To reverse the rotation, tap the reverse button and pull
the trigger when the tool's head is stopped. The power
lamp starts blinking, and the tool's head rotates in
reverse direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the tool's head stops.
► Fig.7: 1. Reverse button
NOTE: During the reverse rotation, the tool operates
only for a short period of time and then automatically
stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you tap the reverse button while the tool's
head is still rotating, the tool comes to stop and to be
ready for reverse rotation.
Electronic torque control function
The tool electronically detects a sudden drop in the
rotation speed which may cause a kickback. In this
situation, the tool automatically stops to prevent further
rotation of cutting tool. To restart the tool, release the
switch trigger. Clear the cause of sudden drop in the
rotation speed and then turn the tool on.
NOTE: This function is not a preventive measure for
kickbacks.
ASSEMBLY
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
Mode
High
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Mounting the handle
Medium
Attach the handle with supplied clamps and bolts. Make
sure that the handle is located between the spacer and the arrow mark. Do not remove or shrink the spacer.
► Fig.8: 1. Handle 2. Hex socket bolt 3. Clamp
Low
Attach the barrier (country specific) to the handle using
the screw on the barrier. Once assembled, do not
remove the barrier.
► Fig.9: 1. Barrier 2. Screw
Mounting the attachment pipe
pipe is secured after installation. Improper instal-
lation may cause the attachment falling off from the
power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1.
ment side.
► Fig.10: 1. Lever
2.
with the arrow mark and insert the attachment pipe until
the release button pops up.
► Fig.11: 1. Release button 2. Arrow mark 3. Pin
3.
► Fig.12: 1. Lever
Make sure that the surface of the lever is parallel to the pipe.
To remove the pipe, turn the lever toward the attach-
ment side and pull the pipe out while pressing down the
release button.
► Fig.13: 1. Release button 2. Lever 3. Pipe
Adjusting the handle/hanger position
Adjust the handle and hanger position to obtain confort-
able handling of the tool.
Loosen the hex socket head bolt on the handle. Move
the handle to a comfortable working position and then
tighten the bolt.
► Fig.14: 1. Handle 2. Hex socket head bolt
Loosen the hex socket head bolt on the hanger. Move
the hanger to a comfortable working position and then
tighten the bolt.
► Fig.15: 1. Hex socket head bolt 2. Hanger
12 ENGLISH
WARNING:
Always be sure that the tool is
WARNING:
Never start the tool unless it is
4. Spacer 5. Arrow mark
CAUTION:
Always check that the attachment
Turn the lever of the power unit toward the attach-
Remove the cap of the attachment. Align the pin
Turn the lever toward the power unit side.