Idiomas disponibles
Idiomas disponibles
PROPER CLOTHING FOR SAFETY
■ Wear close-fitting clothing. Always wear heavy, long
trousers, boots, and gloves. Do not wear jewellery,
shorts, sandals, or go barefoot. Do not wear loose
fitting clothing, which could be drawn into the engine or
catch the chain or undergrowth. Wear overalls, jeans,
or leggings made of cut-resistant material or ones that
contain cut-resistant inserts. Secure hair so that it is
above shoulder level.
■ Wear non-slip safety footwear and heavy-duty gloves
to improve your grip and to protect your hands.
■ Wear eye, hearing, and head protection when
operating this equipment.
REFUELLING (DO NOT SMOKE!)
■ To reduce the risk of fire and burn injury, handle fuel
with care. It is highly flammable.
■ Mix and store fuel in a container approved for petrol.
■ Mix fuel outdoors where there are no sparks or flames.
■ Select bare ground, stop the engine, and allow it to
cool before refuelling.
■ Loosen the fuel cap slowly to release pressure and to
keep fuel from escaping around the cap.
■ Tighten the fuel cap securely after refuelling.
■ Wipe spilled fuel from the unit. Move 9 m away from
refuelling site before starting engine.
■ Never attempt to burn off spilled fuel under any
circumstances.
BASIC PRECAUTIONS IN THE CUTTING/WORK AREA
■ Do not stand on any unstable surface while using your
chainsaw, that includes ladders, scaffolds, trees, etc.
■ Do not start cutting until you have a clear work area,
secure footing, and a planned retreat path from the
falling tree.
■ Do not cut from a ladder, this is extremely dangerous.
■ Use extreme caution when cutting small-size brush
and saplings because slender material may catch the
saw chain and be whipped toward you or pull you off
balance.
■ When cutting a limb under tension, be alert for spring-
back so that you will not be struck when the tension in
the wood fibres is released.
■ Do not operate a chainsaw in a tree unless you have
been specifically trained to do so.
■ Beware of the emission of exhaust gases, lubricant
mist and saw dust.
■ This product is very noisy when operating, to prevent
long term hearing damage, wear hearing protection
and keep other persons 15 m away from the work
English (Original Instructions)
■ Use of hearing protection reduces the ability to hear
■ Keep bystanders and animals out of the work area. Do
NOTE: The size of the work area depends on the job being
performed as well as the size of the tree or work piece
involved. For example, felling a tree requires a larger work
area than making other cuts, i.e., bucking cuts etc.
PUSH AND PULL
The reaction force is always opposite to the direction the
chain is moving. Thus, the operator must be ready to
control the pull when cutting on the bottom edge of the bar
and the push when cutting along the top edge.
NOTE: Your chainsaw has been fully factory tested. It is
normal to find some slight lubricant residue on the saw.
MAINTENANCE PRECAUTIONS
■ Never operate a chainsaw that is damaged, improperly
■ Be sure that the saw chain stops moving when the
■ Keep the handles dry, clean, and free of lubricant or
■ Follow the sharpening and maintenance instructions
■ Use only the replacement guide bars and low kickback
All chainsaw service, other than the items in the
operator's manual maintenance instructions, should be
performed by competent chainsaw service personnel.
If improper tools are used to remove the flywheel or
clutch, or if an improper tool is used to hold the flywheel
in order to remove the clutch, structural damage to the
flywheel could occur which could subsequently cause
the flywheel to burst and serious injury could result.
21
area. Operating similar tools nearby increases risk of
injury. Take frequent breaks.
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the work area.
not allow other persons to be nearby during starting or
cutting with the chainsaw.
adjusted, or is not completely and securely assembled.
throttle control trigger is released. If the saw chain
moves at idling speed, the carburettor may need
adjusting. Refer to "Operation-adjusting idling speed"
later in this manual. If the saw chain still moves at
idling speed after adjustment has been made, contact
a Ryobi service dealer for adjustment and discontinue
use until the repair is made.
fuel mixture.
for the saw chain.
chains specified for your saw. You must never modify
or remove parts from this product or use parts not
recommended by Ryobi. This will increase the risk of
injury.
WARNING
