Idiomas disponibles
Idiomas disponibles
. SETTING THE TIMER
This option does not interrupt or activate cooking but allows you to
use the minute minder both while a function is active and when the
oven is off.
CLEANING AND MAINTENANCE
Make sure that the oven has cooled down before carrying out any maintenance or cleaning. Do not use steam cleaners. Do not
use wire wool, abrasive scourers or abrasive/corrosive cleaning agents, as these could damage the surfaces of the appliance. Wear
protective gloves. The oven must be disconnected from the mains before carrying out any kind of maintenance work.
EXTERIOR SURFACES
Clean surfaces with a damp microfibre cloth. If they are very dirty,
add a few drops of pH-neutral detergent. Finish off with a dry cloth.
Do not use corrosive or abrasive detergents. If any of these products
inadvertently comes into contact with the surfaces of the appliance,
clean immediately with a damp microfibre cloth.
INTERIOR SURFACES
After every use, leave the oven to cool and then clean it, preferably
while it is still warm, to remove any deposits or stains caused by
food residues. To dry any condensation that has formed as a result
of cooking foods with a high water content, leave the oven to cool
completely and then wipe it with a cloth or sponge. Activate the
"Diamond Clean" function for optimum cleaning of internal surfaces
(Available only on certain models).
Clean the glass in the door with a suitable liquid detergent.
ACCESSORIES
Soak the accessories in a washing-up liquid solution after use, handling
them with oven gloves if they are still hot. Food residues can be
removed using a washing-up brush or a sponge.
LOWER THE TOP HEATING ELEMENT (Only in some models)
The top heating element of the grill can be lowered to clean the upper
panel of the oven: Extract the heating element from its seating, then
lower it. To return the heating element to its position, lift it up, pull it
slightly towards you and make sure that the tab support is in its proper
seating.
REMOVING AND REFITTING THE DOOR
To remove the door, open it fully and lower the catches until they are
in the unlock position (1). Close the door as much as you can (2). Take
a firm hold of the door with both hands - do not hold it by the handle.
Simply remove the door (3) by continuing to close it while pulling it
upwards (a) at the same time until it is released from its seating (b).
~60°
2
1
Put the door to one side, resting it on a soft surface. Refit the door by
moving it towards the oven, aligning the hooks of the hinges with their
seating and securing the upper part onto its seating. Lower the door
and then open it fully. Lower the catches into their original position:
make sure that you lower them down completely. Try closing the door
and check to make sure that it lines up with the control panel. If it does
not, repeat the steps above.
TROUBLESHOOTING
What to do if...
The oven is not working.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
•
Visiting our website
•
Using QR Code
•
Alternatively,
contacting our After-sales Service, please state the codes provided on your product's identification
plate.
a
3
Possible reasons
Power cut.
Disconnection from the mains.
docs . hotpoint . eu
contact our After‑sales Service
To activate the timer, turn the timer knob fully clockwise
and then return it to desired duration, proceeding counterclockwise:
an acoustic signal will warn you when the countdown is finished.
CLICK & CLEAN ‑ CLEANING THE GLASS
After removing the door and resting it on a soft surface with the
handle downwards, simultaneously press the two retaining clips (1) and
remove the upper edge of the door by pulling it towards you (2).
1
Lift and firmly hold the inner glass with both hands, remove it and
place it on a soft surface before cleaning it (3).
3
To correctly reposition the inner glass, make sure that the "R" is visible
in the left-hand corner and the clear surface (not printed) is facing up.
First insert the long side of the glass indicated by "R" into the support
seats, then lower it into position (4). Refit the upper edge (5): a click
will indicate correct positioning. Make sure the seal is secure before
refitting the door.
4
~15°
REPLACING THE LAMP
b
Disconnect the oven from the power supply, unscrew the cover from
the light, replace the bulb and screw the cover back on the light.
Reconnect the oven to the power supply. Do not use the oven until the
light cover has been refitted.
Please note: Only use 25W/230 ~ V, G9 type, T300°C halogen bulbs. The
bulb used in the product is specifically designed for domestic appliances
and is not suitable for general room lighting within the home. Light bulbs
are available from our After-sales Service.
Solutions
Check for the presence of mains electrical power and whether the
oven is connected to the electricity supply.
Turn off the oven and restart it to see if the fault persists.
(See phone number in the warranty booklet). When
2
5
Model: xxxXXXXxx
XXXXXXXXXXXXXX
