Idiomas disponibles
Idiomas disponibles
24 | English
Speed preselection
You can preselect the required speed using the speed preselection thumbwheel (6), even during operation. The information in
the table below describes the recommended values.
Material
Application
Metal
Removing paint
Metal
Brushing, removing rust
Stainless steel
Grinding
Metal
Rough grinding
Metal
Cutting
Stone
Cutting
The rated speed of the accessory must be at least
u
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
Speed preselection level
1
2
3
4
5
6
The values specified for speed levels are guide values.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard
(9) onto the holder on the
power tool until the coding
cams of the protective guard
are aligned with the holder.
When doing so, press and
hold the unlocking lever (1).
Press the protective guard
(9) onto the spindle collar un-
til the shoulder of the pro-
tective guard is sitting on the
flange of the power tool and
rotate the protective guard
until it audibly clicks into
place.
Adjust the position of the protective guard (9) to meet the
1 609 92A 6A1 | (14.02.2022)
Application tool
Sanding sheet
Cup brush, abrasive disc
Grinding disc/fibre disc
Grinding disc
Cutting disc
Diamond cutting disc
requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (9) into
the required position.
Always position the protective guard (9) such that the
u
two cams on the unlocking lever (1) engage in the
-1
[min
]
corresponding openings on the protective guard (9).
2800
Adjust the protective guard (9) such that sparking in
u
4500
the direction of the operator is prevented.
The protective guard (9) must only be adjustable
6200
u
while the unlocking lever (1) is actuated. Otherwise,
7900
the power tool must not be used any more under any
9600
circumstances and must be sent to the after-sales ser-
11,500
vice.
Note: The coding cams on the protective guard (9) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
For cutting, always use the protective guard for
u
cutting (11) or the protective guard for grinding (9)
together with the cover for cutting (13).
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (11) is fitted in the same
way as the protective guard for grinding (9).
Metal cover for cutting
Fit the metal cover for cutting (13) on the protective guard
for grinding (9) (see figure A): Swivel the tool retainer back
(➊). Attach the cover (13) to the protective guard for
grinding (9) (➋). Press the tool retainer firmly into place on
the protective guard (9) (➌).
To remove the cover (see figure B), press the button on the
tool retainer (➊) and swivel it back (➋). Remove the
cover (13) from the protective guard (9) (➌).
Plastic cover for cutting
Attach the plastic cover for cutting (13) to the protective
guard for grinding (9) (see figure C). The cover (13) audibly
and visually engages on the protective guard (9).
To remove the cover (see figure D), unlock the cover (13) on
the left- or right-hand side of the protective guard (9) (➊)
and remove the cover (➋).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a cutting guide (25) is
fitted in the same way as the protective guard for grinding.
Thumbwheel position
2–3
3
4–6
6
6
6
Bosch Power Tools
