Water Softener; Detergent Use - cecotec BOLERO AGUAZERO 6000 Manual De Instrucciones

ENGLISH
1. Set the water softener.
2. Add salt to the water softener.
Load the baskets.
3.
Fill the detergent compartment.
4.
Fig. 11
4.1. Dishwasher salt
Use only salt special for dishwashers.
The salt compartment is located under the lower basket.
Filling the compartment with dishwasher salt
Fig. 12
1. Remove the lower basket and loosen the compartment cap.
Open the salt compartment cap by turning it counterclockwise.
2.
Fill the compartment with dishwasher salt until it is almost full. Using a funnel will make
3.
the process easier.
4. Add water to the salt compartment until the limit (only in the first use). It is normal for a
small amount of water to come out of the salt compartment.
Place the cap back and tighten it.
5.
6. The salt indicator light will turn off after the salt compartment is filled with salt.
- When running the dishwasher, the salt compartment will fill with water, so you must fill
the compartment before running the dishwasher.
- Fill the salt compartment immediately before running the dishwasher as, otherwise, the
filtering system, pump and other important parts of the machine may get damaged. The
guarantee shall not cover this eventuality.
Note
You must only refill the salt compartment when the salt indicator lights up on the control
panel. Depending on how well the salt is dissolved, the salt indicator light may remain on, even
if the salt compartment is full.

4.2 Water softener

- This dishwasher is equipped with a water softener which uses a salt compartment
specifically designed to reduce water hardness.
- To find out the hardness level of your tap, you can contact your water company or use a
test strip.
- You must set the water softener manually according to the water hardness in your area,
to do so use the water hardness dial. The goal is to optimise and customise the salt
consumption level.
70
Water hardness table
Germany water France water hardness
hardness level (dH) level (dF)
0-5 0-9
6-11 10-20
12-17 21-30
18-22 31-40
23-34 41-60
35-55 61-98
NOTE: water hardness is set in H3 by default. If water comes from a well or its water
hardness is over 90 dF, it is recommended to use refinement filters and devices.
Setting the water softener
1. Close the dishwasher door and turn it on by pressing the power button.
Wait for a minute and hold down the half load button for more than 5 seconds and access
2.
the water softener setting mode.
3. Press the half load button again to select the water hardness level suitable according to
the previous table.
Press the power button to save settings.
4.

4.3 Detergent use

- Use only detergents designed specifically for household dishwashers. Keep the detergent
in a cool, dry place and out of reach from children.
- The ingredients used in the detergents are necessary to remove dirt from the dishwasher.
- Do not fill the compartment with powder detergent until it is ready to wash the tableware.
- The necessary detergent quantity will depend on the cycle, the load size and the tableware
soiling level. Add an adequate quantity to ensure optimum performance.
- If the detergent amount is too high, you will notice glass and dishes have whitish stripes
or bluish layers, which may rust the tableware. Continued use of too much detergent may
cause damage to the dishwasher.
- If the amount of detergent is too low, it can cause bad cleaning, as well as whitish stripes
if the water is hard.
- Check the manufacturer instructions for the detergent to get more information.
ENGLISH
United Kingdom water Indicator on
hardness level (dE) the display
0-6 H1
7-14 H2
15-21 H3
22-28 H4
29-42 H5
43-69 H6
71
AGUAZERO 6000/SILVER