General Safety Rules; Safety Instructions; Electrical Safety; Personal Safety - Black and Decker PRO Serie Manual De Instrucciones

DO NOT RETURN THIS PRODUCT TO THE STORE,
first contact your local Black & Decker office or nearest
authorized service center.

GENERAL SAFETY RULES

Warning! Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS

General power tool safety warnings.
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions listed
below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
All manuals and user guides at all-guides.com

3. Personal safety

a. Stay alert, watch what you are doing and use common
b. Use personal protective equipment. Always wear
c. Prevent unintentional starting. Ensure the switch is in
d. Remove any adjusting key or wrench before turning
e. Do not overreach. Keep proper footing and balance at
f.
g. If devices are provided for the connection of dust
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
b. Do not use the power tool if the switch does not turn it
c. Disconnect the plug from the power source and/or the
d. Store idle power tools out of the reach of children and
e. Maintain power tools. Check for misalignment or
21
protected supply. Use of an RCD reduces the risk of
electric shock. NOTE: The term "Residual Curent Device
(RCD)" can be replaced by "Ground Fault Circuit Interrupter
(GFCI)" or by "Earth Leakage Circuit Breaker (ELCB)".
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
can reduce dust related hazards.
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
binding of moving parts, breakage of parts and any
ENGLISH