Inserting The Battery; Replacing The Battery - Hama 00186414 Instrucciones De Uso

G Operating instruction
Controls and Displays
1. Back case
2. Battery compartment
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your attention
to speci c hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
2. Package Contents
• Wall clock
• 1 (AA) battery
• These operating instructions
3. Safety Notes
• Protect the product from dirt, moisture and overheating, and only use it in
a dry environment.
• Do not use the product in areas where the use of electronic devices is not
permitted.
• Do not drop the product and do not expose it to any major shocks.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach of children due to the risk
of suffocation.
• Dispose of packaging material immediately according to locally applicable
regulations.
Warning – Batteries
• When inserting batteries, note the correct polarity (+ and - markings)
and insert the batteries accordingly. Failure to do so could result in the
batteries leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the speci ed
type.
• Before you insert the batteries, clean the battery contacts and the polar
contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or
make.
• Remove the batteries from products that are not being used for an
extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a re.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the
environment. They can contain toxic, environmentally harmful heavy
metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging or using batteries in extreme temperatures.
2
4. Getting Started

4.1 Inserting the battery

Remove the battery that was already inserted into the clock, remove the
protective lm if necessary as well as the contact interrupter and the re-insert
the battery with the correct polarity. The clock is ready for operation.

4.2. Replacing the battery

• Open the battery compartment on the back of the product.
• Remove and dispose of any used batteries. Insert the new battery (AA).
Ensure that the polarity of the battery corresponds to the symbols in the
battery compartment.
• Close the battery compartment.
5. Installation
• You can use the suction cups on any glass surfaces, including mirrors,
glass or tiles. Moisten the suction cups before attaching the clock for a
more secure hold. Ensure that there is no dust or grease on the surface on
which you want to attach the suction cups. The suction cups could loosen
over time; to prevent the clock from falling, press the suction cups against
the wall every now and then to ensure that the clock remains xed on the
wall. Attach the clock to the wall in an area where it will not be damaged
if it should fall.
• The clock is also equipped with a slot for wall mounting on the back side,
so that you can attach it to the wall using a nail or a screw.
Warning – Mounting Note
• Before mounting the clock, ensure that the chosen wall is suitable for
the weight to be mounted, and make sure that there are no electrical
wires, water, gas or other lines at the installation site on the wall.
• Purchase special fastening materials from specialised dealers.
6. Operation
• Once the battery has been inserted properly, the clock will automatically
start running.
• Use the setting wheel on the back of the clock to set the time.
7. Care and Maintenance
Only clean this product with a slightly damp, lint-free cloth and do not use
aggressive cleaning agents. Make sure that water does not get into the
product.
8. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for
damage resulting from improper installation/mounting, improper use of the
product or from failure to observe the operating instructions and/or safety
notes.
9. Technical Data
Wall clock
Power supply 1.5 V
1 x AA battery
a