Nice TTDMD Instrucciones Y Advertencias De Instalación Y Uso página 12

dimmer up again. Wait for the green led to turn on and the lamp to turn on at
minimum brightness. Release the external button.
02. Hold down the external button; the green led turns on and then off again; the
lamp's brightness increases and then decreases; release the button.
03. Hold down the external button; the green led turns on and then off again; the
lamp's brightness increases and then decreases; when the green led and the
lamp start flashing, release the external button after the fifth flash.
04. Hold down the external button; the green led turns on and then off again; the
lamp's brightness increases and then decreases; when the green led and the
lamp start flashing, release the external button after the second flash. If the pro-
cedure was a success the dimmer's led will briefly flash green 2 times, and the
lamp will stay on at minimum brightness.
13 - LOCKING AND UNLOCKING THE MEMORY
As said in Chapter 8, you can memorize new transmitters using a previously memo-
rized transmitter. When doing so, if another Nice transmitter with rolling code encod-
ing is transmitting in the vicinity of the dimmer, there is a risk that it be unintentionally
memorized in the dimmer. To avoid this, you can lock the dimmer's memory as follows.
13.1 - Locking/unlocking the memory (using a previously
memorized transmitter)
This procedure can only be done with a Mode I transmitter.
Before starting, turn on the lamp, set it to minimum brightness, and turn it off.
01. Hold down the button n on the transmitter; wait for the dimmer's led to flash
once green and the lamp to increase its brightness to the maximum. Now re-
lease the button.
02. Hold down the button t on the transmitter; wait for the dimmer's led to briefly
flash green 2 times and the lamp to decrease its brightness to 10%. Now release
the button.
03. Hold down the button s on the transmitter; wait for the dimmer's led to briefly
flash green 3 times and the lamp to increase its brightness to 50%. Now release
the button.
04. Hold down the button s on the transmitter; wait for the dimmer's led to briefly
flash green 4 times and the lamp to decrease its brightness to 10%. Now release
the button.
05. Select the desired option from the list:
• to lock the memory (= use button s);
• to unlock the memory (= use button n).
Now hold down the transmitter button indicated in the option in question; wait
for the led to flash green 2 times and turn off. Now release the button.
11 – English
13.2 - Locking/unlocking the memory (using the dimmer's button)
01. Hold down the dimmer button until the green led turns on and off; release the
button.
02. Hold down the dimmer button until the led turns on green, turns off and then
flashes green 2 times; release the button.
03. Hold down the dimmer button until the led turns on green, turns off and then
flashes green 2 times; release the button.
04. Select the desired option from the list, then slowly press the dimmer's button the
corresponding number of times:
• to lock the memory (= 1 press);
• unlock the memory (= 2 presses).
Wait 10 seconds for the led to flash green the number of times indicated for the
selected option.
05. Hold down the dimmer's button; wait for the green led to turn on and off, then
release the button: the led will flash green briefly 2 times to confirm the deletion.
13.3 - Locking/unlocking the memory (using an external button)
Before starting, turn on the lamp, set it to minimum brightness, and turn it off.
01. Shut off power to the dimmer; hold down the external button, then power the
dimmer up again. Wait for the green led to turn on and the lamp to turn on at
minimum brightness. Release the external button.
02. Hold down the external button; the green led turns on and then off again; the
lamp's brightness increases and then decreases; the green led and the lamp
flash 2 times. Release the external button.
03. Hold down the external button; the green led turns on and then off again; the
lamp's brightness increases and then decreases; the green led and the lamp
flash 2 times. Release the external button.
04. Press the external button the number of times corresponding to the option you
wish to program:
• to lock the memory (= 1 press);
• unlock the memory (= 2 presses).
10 seconds after the last press, the green led and the lamp flash the same num-
ber of times.
05. Press the external button and hold it down. The green led turns on and the
lamp's brightness increases; as soon as the led turns off and the lamp's bright-
ness has decreased again, release the button. As a confirmation, the green led
and lamp will flash 2 times.