Protecting The Environment; Service Information - BLACK&DECKER PRO Serie Manual De Instrucciones

Removing
Remove the screws (9).
Take the guard off the tool.
Warning! Never use the tool without the guard.
Adjusting the guard (fig. B)
The guard can be rotated 180°.
Slacken the screws (9) and the nut (10).
Rotate the guard as required.
Re-tighten the screws and the nut.
Fitting the side handle
Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data). The maximum thickness for grinding
discs is 6 mm, for cutting discs 3.5 mm.
Fitting
Fit the guard as described above.
Place the inner flange (11) onto the spindle (6) as shown
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (6) as shown (fig. D).
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
Place the outer flange (14) onto the spindle. When fitting
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. E). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. E).
Keep the spindle lock (4) depressed and tighten the outer
flange using the two-pin spanner (15) (fig. F).
Removing
Keep the spindle lock (4) depressed and loosen the outer
flange (14) using the two-pin spanner (15) (fig. F).
Remove the outer flange (14) and the disc (12).
USE
Warning! Let the tool work at its own pace. Do not
overload.
Carefully guide the cable in order to avoid accidentally
cutting it.
Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
Always position the tool in such a way that the guard provides
optimum protection from the grinding or cutting disc.
Switching on and off
To switch the tool on, press the lock-off button (2) and
subsequently press the on/off switch (1).
To switch the tool off, release the on/off switch (1).
Warning! Do not switch the tool off while under load.
Hints for optimum use
Firmly hold the tool with one hand around the side handle
and the other hand around the main handle.
When grinding, always maintain an angle of approx. 15°
between the disc and the workpiece surface.
MAINTENANCE
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste. Should
you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the retailer
when you purchase a new product.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and
authorized service locations. All Black & Decker Service Centers
are staffed with trained personnel to provide customers with
efficient and reliable power tool service. Whether you need
technical advice, repair, or genuine factory replacement parts,
contact the Black & Decker location nearest you, or visit us at
www.BlackandDecker-la.com
15
ENGLISH