Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Removing
Use a screwdriver to remove the screws (10).
u
Remove the flange (9), guard (6) and spring washer (8).
u
Store these parts carefully.
Warning! Never use the tool without the guard.
Adjusting the guard
The guard can be rotated 90°.
Rotate the guard as required.
u
Fitting the side handle
Screw the side handle (4) into one of the mounting holes
u
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data).
Fitting
Fit the guard as described above.
u
Place the inner flange (11) onto the spindle (7) as shown
u
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (7) as shown (fig. C).
u
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
u
Place the outer flange (14) onto the spindle. When fitting
u
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. D). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. D).
Keep the spindle lock (5) depressed and tighten the outer
u
flange using the two-pin spanner (15) (fig. E).
Removing
Keep the spindle lock (5) depressed and loosen the outer
u
flange (14) using the two-pin spanner (15) (fig. E).
Remove the outer flange (14) and the disc (12).
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
u
cutting it.
Be prepared for a stream of sparks when the grinding or
u
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
u
provides optimum protection from the grinding or cutting
disc.
Switching on and off
To switch the tool on, press the lock-off button (2) and
u
subsequently press the on/off switch (1).
For continuous operation, press the lock-on button (3) and
u
release the on/off switch.
To switch the tool off, release the on/off switch. To switch
u
the tool off in continuous operation, press the on/off switch
once more and release it.
Warning! Do not switch the tool off while under load.
Hints for optimum use
Firmly hold the tool with one hand around the side handle
u
and the other hand around the main handle.
When grinding, always maintain an angle of approx. 15°
u
between the disc and the workpiece surface.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack,
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in you appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new plug.
u
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
ENGLISH
9
Tabla de contenido
