Finishing; Front Panel Removal And Installation; Test Run - Fujitsu ASYG14LECA Manual De Instalación

8. FINISHING

(1) Insulate between pipes.
• Insulate suction and discharge pipes separately.
• For rear, right, and bottom piping, overlap the connection pipe heat insulation and
indoor unit pipe heat insulation and bind them with vinyl tape so that there is no
gap.
• For left and left rear piping, butt the connection pipe heat insulation and indoor unit
pipe heat insulation together and bind them with and vinyl tape so that there is no
gap.
• For left and left rear piping, wrap the area which accommodates the rear piping
housing section with cloth tape.
• For left and left rear piping, bind the
connection cable to the top of the pipe with
vinyl tape.
• For left and left rear piping, bundle the piping
and drain hose together by wrapping them
with cloth tape over the range within which
they fi t into the rear piping housing section.
(2) Temporarily fasten the connection cable
along the connection pipe with vinyl tape.
(Wrap to about 1/3 the width of the tape
from the bottom of the pipe so that water
does not enter.)
(3) Fasten the connection pipe to the outside
wall with a saddle, etc.
(4) Fill the gap between the outside wall pipe
hole and the pipe with sealer so that rain
water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
Wall
Overlap the insulation
Connection pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
Pipe
Drain hose
Left piping
Connection cable
Pipe
Drain hose
Check the following:
NO GOOD NO GOOD NO GOOD
GOOD
Drain hose
Saddle
Lifted up

9. FRONT PANEL REMOVAL AND INSTALLATION

9.1. Intake grill removal
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the intake grille is removed.
9.2. Intake grill installation
(1) The fi xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
En-7
All manuals and user guides at all-guides.com
Intake grille
Knob
Intake grille
Mounting shaft
Bearing
Front panel
Outside wall cap*
Sealer putty*
(Outdoors)
*Field supplied
Indoor unit pipe
(heat insulation)
Vinyl tape
Wrap with cloth tape
Cloth tape
For connection from the left rear
Wall pipe Connection cable
Drain hose Connection pipe
Wave End in water
9.3. Front panel removal
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove wire cover.
(3) Remove 3 screws.
Screws (3 position) Screws (Wire cover)
Push the [▲] marks.
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
9.4. Front panel installation
(1) First, fi t the lower part of the front panel, and insert top and bottom hooks. (3 top
sides, 6 bottom sides, 2 center)
Indoor
unit
Bottom holes
(6 position)
Top holes (3 position)
Center hooks
Indoor unit
(2 position)
(2) Attach the 3 screws.
(3) Attach the wire cover.
(4) Attach the intake grille.
CAUTION
Install the Front panel and Intake grille securely. If installation is imperfect, the Front
panel or Intake grille may fall off and cause injury.

10. TEST RUN

Check items
(1) Is operation of each button on the remote control unit normal?
(2) Does each lamp light normally?
(3) Do air fl ow direction louvers operate normally?
(4) Is the drain normal?
(5) Do not have an abnormal noise and vibration during operation?

Do not operate the air conditioner in test run for a long time.
[Operation method]
 For the operation method, refer to the operating manual.
 The outdoor unit, may not operate, depending on the room temperature. In this
case, keep on pressing the MANUAL AUTO button of the indoor unit for more than
10 seconds. The operation indicator lamp and timer indicator lamp will begin to fl ash
simultaneously during cooling test run. Then, heating test run will begin in about three
minutes when HEAT is selected by the remote control operation. (Please follow the
operating manual for remote control operation.)
Wire cover
Wall hook bracket
Front panel
Bottom hooks (6 position)
Front panel
Top hooks
(3 position)
Front panel
Latchs (2 position)