Tabla de contenido
Idiomas disponibles
Idiomas disponibles
reloop mode, PGM, repeat modes, the playback display
bar, and three different time displays. These times dis-
plays are TIME ELAPSED on the track, TIME REMAINING
on the disc and TIME REMAINING on the track. Time is
measured in minutes, seconds and frames.
10
PGM: Allows you to create a set playlist. To program a
set list into the CDX-1210 memory, begin by stopping the
unit from play and pressing PGM to begin the set list. Se-
lect a track by using the track selection rotary to scan to
the first track to be placed in the set list. When you have
selected the proper track press PGM and the CDX-1210
will be ready to set your next selection. Repeat the previ-
ous steps until you have completed your play list, then
press play to begin the set list.
REPEAT: Press the repeat button once to engage 1 or re-
11
peat the selected track. Press REPEAT again to engage
the ALL setting, which repeats all the tracks on the CD.
Press REPEAT again to disengage the repeat function.
SINGLE: Pressing the SINGLE button engages SINGLE
12
mode, in this mode the CDX-1210 will play one song and
then stop. Pressing the SINGLE button again will then
activate CONTINUOUS mode causing the unit to play
continuously (after the last track, the unit will return to
the first track of the disc and continue to play).
TIME: The TIME button switches the time display between
13
three available sources, these three are TIME ELAPSED
on the track, TOTAL REMAIN on the disc and REMAIN on
the track. TIME ELAPSED indicates how much time has
currently gone by since the play button was pressed, TO-
TAL REMAIN will count down the time remaining on the
entire disc and REMAIN counts down the time that is left
before the end of the track.
PITCH: Hold the PITCH button to activate the PITCH
14
CONTROL SLIDE. Press the PITCH button to switch be-
tween 4%, 8%, and 16% pitch ranges that can be con-
trolled through the use of the PITCH CONTROL SLIDER.
Hold the PITCH button again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL
15
SLIDE up or down will change the pitch percentage +/ -
4, 8, or 16%.
16
PITCH BEND: Pushing the PITCH BEND BUTTONS will
automatically raise the pitch up to +16% or lower the
pitch down to -16% from the existing pitch setting. Re-
leasing the buttons will return the pitch to the original
pitch setting. You can use this function to match the beat
when mixing from one song to another.
LOOP SECTION: LOOP SECTION: A LOOP repeats the
17
section between the entry point (LOOP IN) and the exit
point (LOOP OUT).
A. To set a loop while the unit is playing, start by press-
ing the LOOP IN BUTTON (it will light up)
B. When you reach the desired end loop point press
the LOOP OUT BUTTON (it will also light up). The LOOP
IN and LOOP OUT BUTTONS will blink. The loop will
continue playing until you press the LOOP OUT BUT-
TON again allowing the music to continue from that
point on.
C. To re-engage the loop you must press the RELOOP
BUTTON.
D. When you have released your loop the LOOP IN BUT-
TON and LOOP OUT BUTTON will remain lit to indicate
that your loop is stored in the CDX-1210 memory.
E. Pressing the LOOP IN BUTTON again while the unit
is playing will erase the previously saved loop while
saving your new loop entry point.
F. Press LOOP OUT to exit the loop and save a new
complete loop.
G. Press RELOOP to return to the beginning of the pre-
viously saved loop from normal play. Press RELOOP
repeatedly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT
POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON
18
causes the operation to change from PLAY to PAUSE or
from PAUSE back to PLAY. The PLAY/PAUSE BUTTON
remains lit when in PLAY mode, while it blinks in PAUSE
mode.
19
CUE: To set a CUE point, press the PLAY/PAUSE BUTTON
while a file is playing and use the JOG WHEEL to locate
a desired CUE point. Pressing the PLAY/PAUSE BUTTON
again will set a CUE point. While the unit is playing and
after the cue point has been programmed, pressing CUE
will cause the CD player to enter the PAUSE mode (PLAY/
PAUSE BUTTON blinks) at the programmed cue point (the
CUE LED is lit). Holding down the CUE button changes the
function to preview, and allows you to stutter start or play
from the programmed CUE POINT. Releasing the CUE but-
ton will return the CD to the preset CUE point.
20
TRACK SELECTION ROTARY: The TRACK SELECTION
ROTARY allows you to select the next or previous track
by either turning it clockwise to go forward or counter-
clockwise to go back. Select the track desired by pressing
the TRACK SELECTION ROTARY.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,
YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE
POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER
AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING
OF THE NEWLY SELECTED TRACK.
21
BRAKE: To engage the BRAKE function, press the BRAKE
button, then press the PAUSE button to perform the brake
CDX-1210
5
Tabla de contenido
