AEG OMNI-JS Manual Original página 5

APPROVAL
This application head is approved for use on the following
powerbases:
OMNI 18C-PB......................................................... 18 V-
OMNI 300-PB ................................................ 220-240 V ~
TECHNICAL DATA OMNI-JS
Production code.............................................. 4407 16 02...
...00001-99999
Stroke rate under no-load ................................ 0-3000 min
Lengths of stroke .................................................... 15 mm
Cutting depth max. in:
Wood ................................................................... 40 mm
Steel ...................................................................... 6 mm
Aluminium ............................................................ 10 mm
Weight according EPTA-Procedure 01/2014 ......... 1.1 kg
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Sawing of wood *1
OMNI 18C-PB .................................................. 4.4 m/s
OMNI 300-PB .................................................. 5.8 m/s
Uncertainty K ................................................... 1.5 m/s
Sawing of sheet metal *2
OMNI 18C-PB .................................................. 3.0 m/s
OMNI 300-PB ................................................ 10.1 m/s
Uncertainty K ................................................... 1.5 m/s
*1 with saw blade HCS, dimension 100 x 8 x 2.0 mm and
tooth pitch 4.0 mm
*2 with saw blade HSS, dimension 76 x 8 x 2.0 mm and
tooth pitch 2.0 mm
For technical data and approvals of powerbases for use with
various application heads please refer to the operating
instructions of the used powerbase.
WARNING
The vibration and noise emission level given in this
information sheet has been measured in accordance with a
standardized test given in EN 62841 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration and noise emission level represents
the main applications of the tool. However if the tool is used
for different applications, with different accessories or poorly
maintained, the vibration and noise emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration and noise
should also take into account the times when the tool is
switched off or when it is running but not actually doing the
job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm,
organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
JIG SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a „live" wire may make
exposed metal parts of the power tool „live" and could give
the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
8 ENGLISH
workpiece by hand or against your body leaves it unstable
and may lead to loss of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
-1
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
2 • it has pierced through the material to be machined
2 • the power tool is overloaded
2
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
2
WARNING! Danger of burns
2
• when changing tools
2
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must first be drilled with a hole
corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the
machine.
Always disconnect the plug from the socket before carrying
out any work on the machine.
The product will restart automatically if stalled. Switch off the
product immediately if it stalls. Do not switch on the product
again while it is still stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the
product stalled and rectify this, paying heed to the safety
instructions.
SPECIFIED CONDITIONS OF USE
Combined with an AEG OMNIPRO powerbase the Jigsaw
Head is designed to cutting wood, plastic and metal; it can
cut straight lines, curves, and internal cut-outs.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfills all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-11:2016 + A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-12-03
Alexander Krug
Managing Director
Authorized to compile the technical file.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfills all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016 + A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-12-03
Alexander Krug
Managing Director
Authorized to compile the technical file.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINTENANCE
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine
(OMNI 18C-PB).
Always disconnect the plug from the socket
before carrying out any work on the machine
(OMNI 300-PB).
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with
household waste material.
Electric tools and batteries that have reached
the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark.
ENGLISH 9