Tabla de contenido
Idiomas disponibles
Idiomas disponibles
•
EDIT SATELLITE
In this submenu you can add, modify, delete satellites and
set their name, LO frequency, 22 KHz, DiSeqC1.0, USALS
as well as the latitude corresponding to the requirements.
Use the directional buttons to select "Add Satellite" and
confirm the selection with [OK] to enter the satellite add
interface (see below).
1.
Press the up or down button to select individual
items and the right or left button to change the
setting of the selected item.
2.
If you need to enter the satellite name or the
selected parameter, press the [OK] button to enter
the change, then use the right or left directional
button to select a letter or number, then the up /
EN
down buttons to change it. After selecting the
appropriate letter or number, press [EXIT].
3.
After adding the satellite, press [EXIT]. Two options
will appear on the screen (see the picture below).
By pressing [OK] you will save the new settings. By
pressing [EXIT] you will leave without saving the
changes.
By going to the "Modify Satellite" with the directional
buttons and pressing [OK], you enter the satellite
modification interface.
1.
Press the up / down buttons to select individual
items to be modified and the right / left buttons to
change the settings.
2.
If you need to change the satellite name or a selected
parameter, press [OK] to select, then use the right or
left directional button to select a letter or number,
then the up or down button to change it. After
making the changes, press [EXIT].
3.
After modifying the satellite, press [EXIT] to go
back to the submenu. A screen will appear with two
options (see the picture below).
To delete a satellite, enter the "Delete Satellite" option. Use
the up or down directional buttons to select the satellite
you want to delete and press [OK]. Then use the [OK]
button again to delete the satellite or the [EXIT] button to
deselect.
•
EDIT TRANSPONDER
You can add, modify and delete transponders in this
submenu.
To add a transponder, select "Add Transponder" in the
submenu and confirm with the [OK] button as in the picture
below.
1.
Satellite: press the left or right directional button to
select an existing satellite.
2.
Trans Freq: to set the transponder frequency, press
[OK] to enter the options, then use the directional
buttons to set the number. Press [EXIT] to leave the
setting mode.
3.
Symbol Rate is the transfer speed of the current
transponder. Set as above.
4.
Polarity:
selection
of
vertical
or
horizontal
polarization.
After adding the transponder, press the [EXIT] button and
follow the on-screen instructions; press [OK] to save the
changes or [EXIT] to leave without saving them.
To modify the available transponder, select "Modify
Transponder" and press [OK] to enter the settings.
14
Use the up / down / right / left directional buttons to
select a satellite, then press [OK] to enter the transponder
interface.
After completing transponder modification, press [EXIT] to
leave this interface and when the selection screen appears,
press [OK] to save the changes or [EXIT] to continue
without saving them.
This function allows you to delete existing transponders.
•
TOOLS
In this submenu you can set "USALS" and calculate the
angle of the satellite using "Angle Calcualtion".
•
„USALS"
1.
Sat .: select a satellite. The satellite USALS must be
set to "ON".
2.
Sat Long .: satellite latitude
3.
Sat Dir .: satellite direction
4.
Trans .: transponder selection
5.
Move: satellite turntable motor settings. Press the
left or right directional button to select east or west
and press [OK]. The dish will rotate 1 degree. If [OK]
is pressed and held, the dish will keep rotating.
6.
Goto: to rotate the dish automatically, press the
left or right directional button to select "XX" or
"ZERO". If you select "XX" and confirm with [OK], the
turntable motor will set the dish automatically to the
appropriate satellite. If you select "ZERO" and confirm
with [OK], the turntable will move to "0" position.
NOTE! Before the "GOTO" function is used, the local
longitude and latitude parameters must be entered
in the "Angle Calculation" submenu.
7.
Set Limit: to set the turntable limiter, press the
left or right directional button to select east, west
or reset the limiter. For example, to set an east
limiter, turn the turntable to the east, then select
"EAST" and confirm with [OK]. This angle will
become the turntable limiter to the east, i.e. the
turntable will not rotate beyond this point. You
can cancel the set limiter by selecting "CLEAR"
•
„ANGLE CALCULATION"
This function is designed to facilitate signal reception and
is used to calculate antenna height, azimuth and the LNB
polarization angle according to the satellite altitude and
the local latitude and longitude settings.
1.
Press the up or down directional button to select the
numerical parameter and confirm with [OK]. Press
the right or left button to select a specific digit and
change it with the up / down buttons. Press [EXIT] to
leave the settings menu.
2.
The letters "E", "W", "N" and "S" mean respectively
east longitude, west longitude, northern hemisphere,
southern hemisphere. Switching between letters
indicating directions can be done with the left / right
directional button.
3.
The angle data can be calculated and displayed
in real time when the parameter is being set. The
elevation is calculated from the horizon upwards,
and the azimuth angle from the north clockwise.
4.
Press [EXIT] to leave the menu.
•
TERRESTIAL
The Terrestrial menu is used for ground signal operations.
•
CHECK CHANNEL
This option allows you to quickly search for terrestrial
signal, its strength and quality, and to set parameters.
15
EN
Tabla de contenido
