Safety Checks; Operating - Stiga PRIMO Instrucciones De Uso

EN
Never completely fill the petrol tank. Leave an
empty space (= at least the entire filler tube plus 1
- 2 cm at the top of the tank) to allow the petrol to
expand when it warms up without overflowing.
5.3 LEVEL CHECK, ENGINE OIL
On delivery, the crankcase is filled with
SAE 10W-30 oil.
Check the oil level every time before using to
ensure it is correct. The machine should be
standing on level ground.
Wipe clean around the oil dipstick (7:S).
Unscrew and pull it up.
Wipe the dipstick.
Slide the dipstick down completely and tighten it.
Pull up the dipstick again. Read off the oil level.
Top up with oil to the "FULL" mark (7:T) if the oil
level is below this mark.
The oil level must never exceed the "FULL" mark.
This can cause the engine to overheat. Drain the oil
to the correct level if the oil level exceeds the
"FULL" mark.

5.4 SAFETY CHECKS

Check that the results of the safety checks below
are met when testing the relevant machine.
The safety checks must always be car-
ried out before use.
If any of the results below are not met,
the machine must not be used. Take the
machine to a service workshop for re-
pair.
5.4.1 General safety checks
Item Result
Fuel lines and No leak.
connections
Power cables All insulation intact.
No mechanical damage.
Exhaust system No leakage in the connections.
All screws tightened.
Test driving No unusual vibrations.
No unusual noise.
5.4.2 Electric safety check
The safety system's function must al-
ways be checked before use.
Status Action
The cutting deck Attempt to
activated. start.
Engine running. The opera-
The cutting deck tor leaves
activated. the seat.
Gear engaged Attempt to
start.
56
All manuals and user guides at all-guides.com
ENGLISH

5.5 OPERATING

5.5.1 Starting the engine
1. Check that the spark plug cable is installed on
2. Check to make sure that the cutting deck is dis-
3. Set the gear control to neutral (N).
4. Starting cold engine – put the throttle control in
5. Depress the clutch – brake pedal fully.
6. Turn the ignition key and start the engine.
7. Once the engine has started, move the throttle
8. When starting from cold, do not make the ma-
5.5.2 Starting driving
Always operate the machine at full throttle when
driving.
1. Depress the clutch – brake pedal fully.
2. Engage the desired gear.
3. Slowly release the clutch-brake pedal fully and
4. Engage the cutting deck.
5.5.3 Driving tips
Ensure that the correct amount of oil is in the en-
Result
gine. Especially when driving on slopes. See 5.3.
The engine should
not start.
The engine should
stop.
The engine should
not start.
Before starting the engine, the actions
in section 5.2 - 5.4 must be carried out.
the spark plug.
engaged.
the choke position.
Starting warm engine – set the throttle control
to full throttle (approx. 2 cm behind the choke
position).
control gradually to full throttle (approx. 2 cm
behind the choke position) if the choke has been
used.
chine work under load immediately, but let the
engine run for a few minutes first. This will al-
low the oil to warm up.
The machine must not be
driven in any direction on
slopes with a gradient
greater than 10º.
See fig. 11.
the machine starts to move in the desired direc-
tion.
Be careful when driving on slopes. No
sudden starting or stopping when mov-
ing up or down a slope. Never drive
across a slope. Move from the top down,
or from the bottom to the top.