Other Operations - Olympus m III 150 Manual De Instrucciones

EN SPECIAL FEATURES
SETTING THE SELFTIMER/REMOTE CONTROL
Press the selftimer/remote control
Mode display Mode
button. The mode switches in the order
No
shown on the left. The selected mode
—————
display
is displayed on the LCD Panel.
Selftimer
Remote Control
Camera Shake
Indicator
Selftimer
Secure the camera on a tripod or other support. Compose your shot in the
viewfinder. Press the shutter release button halfway (the focus and
exposure are locked at this time). Then press the shutter release button all
the way. The selftimer indicator lights for about 10 seconds and then blinks
for about 2 seconds. After this, the shutter will release.
Remote Control RC-300C
(Optional)
Compose your shot in the viewfinder. Position the autofocus frame on your
subject. To take a picture, point the remote control at the camera and
press the button on the remote control. The selftimer/remote control
indicator starts blinking, and the shutter will release about 3 seconds later
(see figure 8 on page 127).
Camera Shake Indicator
In this mode, the camera warns you before you shoot if camera shake is
likely to cause blurring. Also, when there is significant camera shake, this
mode helps reduce blurring. If the green and orange lamps blink
alternately when you hold the camera, it means that the camera is shaking
and blurring may result. Hold the camera securely until the lamps stop
blinking; then press the shutter release button.

OTHER OPERATIONS

REWINDING THE FILM MID-ROLL
Press the mid-roll rewind button with the
1
protrusion on the strap buckle
use an instrument with a sharp tip.
Unload the film as described on page 7.
10
OTHER OPERATIONS
PRINTING THE DATE/TIME
None
Year-month-day
Month-day-year
Day-month-year
Day-hour-minute
CORRECTING THE DATE AND TIME
(Quartzdate model only)
Be sure to correct the date and time after the battery has been inserted or
replaced.
1. Keep the MODE button pressed until the "year" indicator starts blinking.
2. Press the SET button to adjust the "year" indicator. If you press the
button once, the number on the display will advance by 1. If you keep
the button pressed, the numbers will run in rapid succession. If you
pass the intended number, keep pressing to return to that number.
3. Press the MODE button once more to make the "month" indicator blink.
Press the SET button to adjust the "month" indicator. As you press the
MODE button, the blinking indicator changes in the order of "year",
"month", "day", "hour" and "minute".
4. Repeat Steps 2 and 3 to set "hour" and "minute". Make sure the
"minute" indicator is blinking.
5. When "minute" has been set, press the MODE button. None of the
indicators will be blinking and date/time correction is now complete.
REPLACING THE REMOTE CONTROL BATTERY
(Optional RC-300C)
If the selftimer/remote control indicator doesn't blink even when you
press the button, replace the battery with a new one (CR2025).
1. Turn the screw on the bottom of the remote control counterclockwise to
loosen.
2. Turn the remote control over, and remove the cover. With the battery
facing up, remove the old battery and insert a new battery as shown.
3. Replace the cover, turn the remote control over, and turn the screw on
the bottom clockwise to tighten (see figure 9 on page 127).
1
. Do not
EN
(Quartzdate model only)
First select the date/time mode you
want to print. Press the MODE
button. Each time you press it, the
mode will switch in the order shown
on the left. Keep the mode you want
to print displayed. Date/time is
imprinted in the lower right corner of
the picture. If the date/time is
superimposed on a bright color like
white, orange, yellow, etc., it may be
difficult to read. When black-and-
white film is used, the date/time may
not be printed.
11