Spare Parts; Technical Specifications - Renfert Basic master Instrucciones Para El Servicio

5.2 Condensation
1. Inspect the water separator.
2. Drain any water off through the valve (Fig. 21).
5.3 Blasting Nozzle
Replacement
1. Refer to insert no. 21-9162 for installation.
2. Inspect for abrasive residue.
3. Inspect the seal ring position.
5.4 View Port Replacement
Please refer to the installation instructions provided
with the new pane (insert no. 21-9811).
5.5 Sandblasting Hose
Replacement
1. Disconnect the sandblasting unit from the com-
pressed air supply (Fig. 4,3,2).
2. Refer to insert no. 21-9162 for the installation
instructions.
5.6 Replacing the Fluorescent
Lamp
Danger of breakage!
Do not press on the fluorescent lamp or try
to bend it when replacing it. We recommend
using gloves or a cloth to protect your hands
in case of breakage.
• Switch off the unit.
• Pull plug out.
• Lightly press light cover on the right side and
remove it (Fig. 7).
• Pull fluorescent lamp horizontally out of the socket
and remove it.
• Vacuum socket as thoroughly as possible.
• Insert new fluorescent lamp in the retainer and
slide it horizontally into the socket (Fig. 8).
• Install lamp cover in the housing on the left side,
then press it to the right until it clicks into position
(Fig. 9).
Use only original Renfert replacement fluore-
scent lamps (see spare parts list).
5.7 Replacing the lamp cover
• Switch off the unit.
• Pull plug out.
• Lightly press lamp cover on the right side and
remove it (Fig. 7).
• Install lamp cover in the housing on the left side,
then press it to the right until it clicks into position
(Fig. 9)
6. Spare Parts
For the order numbers of consumables and spare
parts please refer to the spare parts list at the end of
this manual.
7. Warranty
Provided the unit is properly used, Renfert warrants
all parts of the Basic master for a period of 3 years.
In case of any claims for warranty original dealers'
invoice is required. Components subject to natural
wear (e.g., blasting nozzles, hoses, fluorescent tubes,
hose connections, view panes, filter materials, etc.)
are excluded from this warranty. The warranty is
voided in case of improper use; failure to observe the
operating, cleaning, maintenance, and connection
instructions; in case of independent repairs or repairs
by unauthorized personnel; if spare parts from other
manufacturers are employed, or; in case of unusual
influences or influences not in compliance with the
utilization instructions. Warranty service shall not
extend the original warranty.
8. Technical Specifications
Working pressure:
Connecting pressure, external: 6 - 8 bar [87 - 116 psi]
Air consumption:
Voltage:
Lamp power consumption:
Cable length:
Ø hose connection:
Ø size of pipe union for external extraction unit:
Dimensions (WxHxD):
Blasting chamber volume:
Tank capacity:
Weight (empty):
Noise level according to DIN 45635-01-KL3:
9. Blasting Notes
Flat blasting with wide nozzles:
No. 90002-1207 0.3 x 3.5 mm [0.012 x 0.138 inch]
No. 90003-1739 1.5 x 3.5 mm [0.059 x 0.138 inch]
When blasting glass ceramics, refer to manu facturer's
notes.
- 15 -
1 - 6 bar [14,5 - 87 psi]
120 l/min. at 6 bar [87 psi]
230 V, 50/60 Hz
100-120 V, 50/60 Hz
16 W
2 m [78,74 inch]
interior: 4 mm [0,16 inch]
exterior: 6 mm [0,24 inch]
interior: 35 mm [1,38 inch]
exterior: 40 mm [1,58 inch]
400 x 285 x 400 mm
[15.76 x 11.23 x 15.76 inch]
18 l
1000 ml each
approx. 7 kg
< 72 dB(A)
EN