Black and Decker GH750 Manual De Instrucciones página 7

ENGLISH
place as shown in figure 9 and position the trimmer above the surface as shown in figure 9.
• Return to the trimming position by unplugging the unit from the power source, pushing the button and
rotating the tube back 180°. The tool will lock in the trimmer position. When using the tool return the wire
edge guide to the original position, out of the way.
BLOWER FUNCTION
The GH750 funnels the air created by the motor up through the guard creating a built-in sweeper. This feature
can be used to blow grass clippings off of sidewalks and other hard surface areas.
CUTTING LINE/LINE FEEDING
Your trimmer uses .065 inch (1.65 mm) diameter, ROUND nylon line. During use, the tips of the nylon lines will
become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of
line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or
other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism
senses when more cutting line is needed and feeds and trims the correct length of line whenever it's required.
DO NOT BUMP unit on ground in attempt to feed line or for any other purposes.
FITTING A NEW SPOOL OF AFS CUTTING LINE (FIGURES 10 & 11)
• Unplug the tool.
• Depress the tabs (a) and remove the cassette (b) from the cassette housing (c) in the trimmer head
(figure 10).
• Grasp empty spool (d) with one hand and cassette with other hand and pull spool out from cassette. If lever
(e) in base of cassette becomes dislodged, replace in correct position before inserting new spool into
cassette.
• Remove any dirt and grass from the cassette and housing.
• Take the new spool and push it onto the boss (f) (figure 11) in the cassette. Rotate the spool slightly until it
is seated.
• Unfasten the end of one of the cutting lines and guide the line into one of the eyelets (g). figure 11. The
line should protrude approximately 4-3/8 inches (111mm) from the cassette.
• Unfasten the end of the other cutting line and guide the line into the other eyelet. The line should protrude
approximately 4-3/8 inches (111mm) from the cassette.
• Align the cassette tabs (a) with the slots (h) in the housing (figure 10).
• Push the cassette onto the housing until it snaps securely into place.
CAUTION! To avoid tool damage, If the cutting lines protrude beyond the trimming blade (i), cut them off
so that they just reach the blade (figure 10).
WINDING NEW LINE ONTO AN EMPTY SPOOL (FIGURES 12 &13)
You may wind new cutting line onto an empty spool. Replacement packs of .065 inch (1.65 mm) cutting line are
available from your local dealer.
• Remove the empty spool from the tool as described in "FITTING A NEW SPOOL OF AFS CUTTING LINE".
• Remove any remaining cutting line from the spool.
• First wind new line onto the uppermost part of the spool.
- Feed 3/4 inch (19mm) of cutting line into one of the line anchoring slots.
- Wind the cutting line onto the spool in the direction of the arrow on the spool.
• Make sure to wind the line on neatly and in layers. Do not crisscross (figure 12).
- When the wound cutting line reaches the recesses (j), cut the line (figure 13).
- Temporarily park the line in the holding slots (k) on one side of the spool as shown in the inset in figure 13.
• Repeat the above procedure for the second cutting line on the lower section of the spool.
• Fit the spool onto the tool as described in "FITTING A NEW SPOOL OF CUTTING LINE".
CAUTION! Before you begin trimming, only use the appropriate type of cutting line. Ensure that cutting line
is present in both sections of the spool (figure 12).
IMPORTANT! To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should
be performed by authorized service centers or other qualified service organizations, always using identical
replacement parts.
WARNING! If the supply cord is damaged, it must be replaced by the manufacturer, an authorized Black &
Decker Service Centre or an equally qualified person in order to avoid a hazard. If the supply cord is replaced
by an equally qualified person, but not authorized by Black & Decker, the warranty will lose effect.
ACCESSORIES
Use Black & Decker replacement spool Model No. DF-065.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.
• USE ONLY .065 inch (1.65 mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use serrated or
heavier gauge line, as they will overload the motor and cause overheating. The unit only functions properly
with .065 inch (1.65 mm) diameter nylon monofilament line. This line is available at your local dealer or
authorized service center.
WARNING! The use of any accessory not recommended by Black & Decker for use with this tool could be
hazardous.
MAINTENANCE
WARNING! To avoid serious injury, switch off and unplug the tool before performing any maintenance.
1. Keep the air intake slots (figure 14) clean to avoid overheating.
2. Your trimmer line can dry out over time. To keep your line in top condition, store spare pre-wound spools or
bulk line in a plastic, sealable bag with a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and a damp rag.
4. The line cutter on the edge of the guard can dull over time. It is recommended you periodically touch-up the
sharpness of the blade with a file.
TROUBLESHOOTING
WARNING! To avoid serious injury, switch off and unplug the tool before performing any maintenance.
Tool runs slowly
• Check that the cassette housing can rotate freely. Carefully clean it if necessary.
• Check that the cutting line does not protrude more than approximately 4-3/8 inches (111mm) from the
cassette. If it does, cut it off so that it just reaches the line trimming blade.
Automatic line feed does not work
• Keep the tabs depressed and remove the cassette from the cassette housing in the trimmer head.
• Pull the cutting line until it protrudes approximately 4-3/8 inches (111mm) from the cassette. If insufficient
cutting line is left on the spool, install a new spool of cutting line.
• Align the tabs on the cassette with the cut outs in the housing.
• Push the cassette onto the housing until it snaps securely into place.
• If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is jammed, try the following suggestions:
• Carefully clean the cassette and housing.
• Remove the spool and check if the lever in the cassette can move freely.
• Remove the spool and unwind the cutting line, then wind it on neatly again. Replace the spool into the
cassette.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations. All Black & Decker
Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool
service. For more information about our authorized service centers and if you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you, or visit us at
www.BlackandDecker-la.com
SPECIFICATIONS
POWER 800W
SPEED n 7300/min (rpm)
0
CUTTING WIDTH 35cm (14")
Solamente para propósito de Argentina:
Importado por: Black & Decker Argentina S.A.
Ricardo Rojas, Partido de Tigre
Black & Decker do Brasil Ltda.
Rod. BR 050, s/n° - Km 167
Uberaba ˆ MG ˆ Cep: 38064-750
CNPJ: 53.296.273/0001-91
Insc. Est.: 701.948.711.00-98
Solamente para propósitos de CCA
Importado por: Black & Decker LLC
Edificio Milano I, Mezanine 5,6 y 7
Solamente para propósitos de Colombia
Importado por: Black & Decker de Colombia, S.A.
Carrera 85D # 51-65, Bodega 23
Complejo Logístico San Cayetano
Solamente para propósito de Chile:
Importado por: Black & Decker de Chile, S.A.
Av. Pdte. Eduardo Frei M. 6001-67 Conchalí
Solamente para propósito de México:
Importado por: Black & Decker S.A. de C.V.
Bosques de Cidros, Acceso Radiatas No.42
3a. Sección de Bosques de las Lomas
Black & Decker del Perú S.A.
Marcos Sastre 1998
Buenos Aires, Argentina
CP: B1610CRJ
Tel.: (11) 4726-4400
Imported by/Importado por:
Dist. Industrial II
S.A.C.: 0800-703-4644
Calle Miguel Brostella Final
El Dorado, Panama
Tel. 507-360.5700
Bogota - Colombia
Tel. 744-7100
Santiago de Chile
Tel. (56-2) 687 1700
Delegación Cuajimalpa,
05120, México, D.F.
Tel. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Av. Enrique Meiggs 227.
Pque. Industrial - Callao
Teléfono: (511) 614-4242
RUC 20266596805
90559268
02/03/10
ENGLISH