Electromagnetic Compatibility - Petzl DUO ATEX LED 5 Manual Del Usuario

(EN) ENGLISH
DUO ATEX LED 5 E61L5 4
Hybrid headlamp for use in hazardous locations
Field of application
The DUO ATEX headlamp may be used in the presence of gases, vapors and
mists, of which the auto-ignition temperature is higher than 200 °C at atmospheric
pressure (200 °C maximum temperature at the surface of the lamp).
This protection corresponds to almost all gases, with the exception of acetylene,
hydrogen, acetaldehyde (C 2 H 4 O) (140 °C), diethyl ether (C 4 H 10 O) (170 °C), ethyl
nitrite (C 2 H 5 NO 2 ) (90 °C) and carbon disulphide (CS 2 ) (102 °C), etc.
The DUO ATEX must not be used in mines where firedamp may be present.
Lexicon: meaning of the marking
The CEI international directive (CEI 79.10 standard of 1995 and the European
directive 94/9/EC; ATEX 95) distinguish the following categories of hazardous
areas: gas, vapors, mists or dusts.
- Zone 0 or 20: the explosive atmosphere is continuously present (tank or silo)
- Zone 1 or 21: the explosive atmosphere is often present (mixing occurring during
the operation of a plant)
- Zone 2 or 22: the explosive atmosphere may be present accidentally (malfunction
of the installation, gas leak)
The DUO ATEX LED 5 is classed Zones 1 and 2 (gas) and zones 21 and 22 (dusts).
It must not be used in Zones 0 or 20.
CE: CE marking
Ex: use of the equipment in an explosive atmosphere
II: group of equipment for surface use
2: device for the present zone 1
G: gas environment
D: dusty environment
EEx: device fulfilling the requirements of the CENELEC standardization (European
standards)
ia: intrinsic protection = protection of the lamp itself, independent of exterior
factors
B: gas subdivision including ethylene
T3: maximum surface temperature of 200 °C
iaD: usage in the presence of combustible dusts
21: zone 21
T200°C: maximum surface temperature of 200 °C
Rechargeable battery
Only use the PETZL E61100 2 DUO ATEX rechargeable safety battery.
WARNING DANGER, do not replace the battery in an explosive atmosphere.
It must never be recharged in an explosive environment.
Instructions for use
Switching on & off, brightness selection
The switch may be locked for transporting or storage by pressing the red button.
To unlock, press on the other end of the red button.
- Switch in upper position: high beam.
- Switch in lower position: proximity lighting using minimum energy.
- The zoom button allows focusing the high beam as needed. In the low position
the beam is narrow. In the high position the beam is wide.
Replacing the rechargeable battery
To open the battery case, unlock the two clips.
Warning, never remove the gasket ring inside the cover. Take care to keep it clean
and properly set in place (clean with water and a cotton ball). Lubricate the ring
with a silicone based grease. If changing batteries in a wet environment, dry the
inside of the box after use.
Prolonged storage: remove battery and leave box open.
Replacing a LED module or bulb
Open the head-piece using the left hand to unscrew the bezel. Remove it
completely. If it jams, try a penetrating fluid, or warm the front cover with a hair
drier.
- LED bulb: unscrew the burned out bulb and screw in the new one, tightening it
securely.
- LED module:
Pull the old one out and insert the new one, taking care not to bend the two metal
contacts.
Check operation by switching the lamp on. If the LED module does not light up,
pull it out, reverse the contacts (turn it 180°) and re-install.
Close the head-piece:
- clean the seal thoroughly, dry the case and grease the seal and the threads with a
silicon-based grease,
- ensure that the reflector/lens/bezel assembly is correctly oriented, screw on
the bezel with the right hand until the mark on the bezel is situated between the
two marks on the case.
Notes
If the lamp is accidentally left on in a small, enclosed space (e.g. kit bag), the heat
generated by the bulb may damage the reflector (take care to lock the switch).
Simultaneous use of both bulbs is not possible: this would only increase power
drain without giving extra light.
This lamp is ideal for wet environments, but it is not a diving light. If either of the
two compartments takes in water (damaged or dirty gasket, poor fitting), open
both boxes, take out batteries and bulbs, rinse in clean water, and allow to dry.
In case of malfunction
Check the state of charge of the battery. Verify that the base of the LED bulb is not
corroded. Remove and replace the LED bulb and module several times, with the
switch in the "on" position. Check that the battery and battery case contacts are not
corroded (clean them if necessary). Work the switch several times.
If your lamp still does not work, contact PETZL.
Do not attempt to disassemble the lamp as this will void the warranty.
Cleaning
Wash the lamp, with the compartments closed, in clean water. Use soap for the
elastics. Do not rub with an abrasive product especially on the lens. Do not wash
with a high pressure cleaner.
DUO ATEX rechargeable battery
DUO charger
Precautions
This notice contains important safety instructions and operating instructions
for DUO CHARGER E65200. Before using this product read all instructions and
cautionary markings on battery charger, battery and products that use this battery.
Save these instructions.
Warning
Only use the PETZL E61100 2 DUO ATEX rechargeable safety battery.
The DUO ATEX E61100 2 rechargeable battery is an intrinsically safe battery of
temperature class T3.
Special safety precaution: the rechargeable battery must never be
recharged in an explosive environment.
DUO ATEX BATTERY E61100 2
6
E61L54_duoatex_E616020K (100613)
Battery capacity: 2700 mAh. The battery consists of four NiMH cells.
To be used only with the Petzl DUO CHARGER.
- The battery must be charged before first use.
- Do not hesitate to recharge a battery that is partially discharged or that has been
in storage for more than two weeks. It is not necessary to fully drain the battery
before recharging.
Self-discharge: a charged battery stored under good conditions at 20 °C loses
about 15 % of its charge after 3 days, then 1 % per day thereafter. Note that this
rate of discharge is greater in higher temperatures.
- It can be recharged 500 times.
- Always keep temperature at which battery is used between -20° C and +60° C.
- Do not place the battery in a fire or dismantle it. An explosion or a release of toxic
materials may result.
- Do not short-circuit the battery. It may cause burns.
Storage
To extend the life of your battery, store it in a clean, dry place at temperatures
between -20° C and +35° C.
Protecting the environment
Lamps, bulbs, and batteries should be recycled. Do not throw them in the regular
trash. Dispose of these items by recycling them in accordance with applicable
local regulations. By doing so you play a part in protecting the environment and
public health.
DUO charger
- Do not recharge alkaline or saline batteries due to a risk of explosion. Other types
of batteries may burst causing personal injury and may damage both batteries
and charger.
- Batteries must always be charged at a temperature between 10 °C and 40 °C.
- Do not expose the charger to rain or snow; electrocution may result.
- Do not operate the charger if it has been subjected to a significant impact or fall.
- If the charger is damaged (the power cable for example), do not disassemble. It
must only be repaired in Petzl workshops as special tools are required.
- To reduce the risk of damage to the plug, pull the plug and not the cable when
unplugging the charger.
- Do not use with an extension cord.
- To avoid the risk of an electric shock, unplug the chargers before attempting any
maintenance or cleaning.
Wall charger: E65200 2
A light flashes when the battery is charging.
Time for complete recharge: 3h30.
When the light is constantly lit, the battery is fully charged. The battery remains so
if left in the charger (trickle charge).
We advise you to keep the battery connected to the wall charger, so it is always
ready for use.
This 100-240 V~, 50/60 Hz charger can be used worldwide with an appropriate
adaptor plug (not supplied). It is compatible with DUO batteries E65100
(1400 mAh) and E65100 2 (2700 mAh).
Car charger: E65300 2
An indicator lights on the battery holder when the battery is charging.
Time for complete recharge:14 hours.
Use only to recharge the Petzl DUO E61100 2. This 12 V charger is not compatible
with the old E61100 (1400 mAh) battery.
Do not charge in a hot car (e.g. parked in the sun); there is a risk of overheating
the battery.

Electromagnetic compatibility

Conforms to the requirements of the 89/336/CEE directive on electromagnetic
compatibility.
Guarantee
This product is guaranteed for 3 years against any faults in materials or
manufacture. Exclusions from the guarantee: normal wear and tear, oxidation,
modifications or alterations, incorrect storage, poor maintenance, damage due to
accidents, to negligence, and to uses for which this product was not designed.
Responsibility
PETZL is not responsible for the consequences, direct, indirect or accidental, or
any other type of damage befalling or resulting from the use of its products.