Low-Battery Indicator; Protecting The Environment - Stanley FATMAX FMC710 Manual De Instrucciones

Variable speed control (fig. I)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the variable speed dial (2) to the desired setting. At
u
setting 1 the tool will operate at low speed, 8,000 min-1.
At setting 6 the tool will operate at the maximum speed,
18,000 min-1.
Switching on and off (fig. J)
To switch the tool on, slide the on/off switch (1) forward
u
(position I).
To switch the tool off, slide the on/off switch (1) to the rear
u
(position O).
LED work light
The LED work light (5) is activated automatically when the tool
is switched on.

Low-battery Indicator

If the LED worklight (5) begins to rapidly and continuously
flash when the switch on the tool is depressed, the battery-
pack power has run out, and the battery pack should be
recharged.
Unlike other battery pack types, Lithium-Ion battery packs
deliver fade-free power for their entire run time. The tool will
not experience a slow, gradual loss of power as you work. To
signal that the battery pack is at the end of its run time and
needs to be charged, the power to the tool will drop quickly.
Note: The LED may also flash due to an overload or high
temperature (see Battery Protection).
Hints for optimum use
Always hold the tool securely. For precision work, hold the
u
tool near the front.
Clamp the workpiece whenever possible, especially when
u
using cutting blades.
Do not exert too much pressure on the tool.
u
Always use the appropriate type of attachment for the
u
workpiece material and type of cut.
Regularly check the condition of accessories. Replace
u
when necessary.
Mark the desired starting point.
u
Switch the tool on and slowly feed attachments into the
u
workpiece at the desired starting point.
Clamp a piece of plywood or soft wood to the back of the
u
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the cutting blade into the workpiece. Note
u
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
When cutting metal spread a thin film of oil along the cut-
u
ting line before cutting.
(Original instructions)
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.

Protecting the environment

Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley Fat Max product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
ENGLISH
9