Lower Blade Guard - DeWalt DCS570 Manual Del Usuario

To Install the Battery Pack into the Tool
Handle
1. Align the battery pack 3 with the rails inside the tool's
handle (Fig. A).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 13
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. A)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button
32 . A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Changing Blades
To Install the Blade (Fig. C–E)
1. Remove the battery.
2. Using the lower guard lever
guard 7 and place blade on saw spindle against the inner
clamp washer , making sure that the blade will rotate
17
in the proper direction (the direction of the rotation arrow
on the saw blade and the teeth must point in the same
direction as the direction of rotation arrow on the saw). Do
not assume that the printing on the blade will always be
facing you when properly installed. When retracting the
lower blade guard to install the blade, check the condition and operation of the lower blade guard to assure that it is
working properly. Make sure it moves freely and does not
touch the blade or any other part, in all angles and depths
of cut.
3. Place outer clamp washer
beveled edge facing out. Make sure the 30 mm diameter on
the blade side of the clamp fits into the 30 mm hole in the
saw blade to ensure centering of the blade.
4. Thread the blade clamping screw
by hand (screw has right-hand threads and must be turned
clockwise to tighten).
5. Depress the blade lock 11
with the blade wrench 14
compartment, until the blade lock engages and the blade
stops rotating.
6. Tighten the blade clamping screw firmly with the
blade wrench.
and firmly pull the battery pack
6 , retract the lower blade
16 on saw spindle with the
8 onto the saw spindle
while turning the saw spindle
stored underneath the battery
NOTICE: Never engage the blade lock while saw is
running, or engage in an effort to stop the tool. Never
turn the saw on while the blade lock is engaged. Serious
damage to your saw will result.
To Replace the blade (Fig. C, D)
1. Remove the battery.
2. To loosen the blade clamping screw
lock 11 and turn the saw spindle with the blade wrench
14 , stored underneath the battery compartment, until
the blade lock engages and the blade stops rotating.
With the blade lock engaged, turn the blade clamping
screw counterclockwise with the blade wrench (screw has
right-hand threads and must be turned counterclockwise
to loosen).
3. Remove the blade clamping screw
washer 16 . Remove old blade.
4. Clean any sawdust that may have accumulated in the
guard or clamp washer area and check the condition and
operation of the lower blade guard as previously outlined.
Do not lubricate this area.
5. Select the proper blade for the application (refer to Blades).
Always use blades that are the correct size (diameter)
with the proper size and shape center hole for mounting
on the saw spindle. Always assure that the maximum
recommended speed (rpm) on the saw blade meets or
exceeds the speed (rpm) of the saw.
6. Follow steps 1 through 5 under To Install the Blade, making
sure that the blade will rotate in the proper direction.

Lower Blade Guard


WARNING: The lower blade guard is a safety feature
that reduces the risk of serious personal injury. Never
use the saw if the lower guard is missing, damaged,
misassembled or not working properly. Do not rely
on the lower blade guard to protect you under all
circumstances. Your safety depends on following
all warnings and precautions as well as proper
operation of the saw. Check the lower blade guard
for proper closing before each use. If the lower blade
guard is missing or not working properly, have the
saw serviced before using. To assure product safety
and reliability, repair, maintenance and adjustment
should be performed by an authorized service center
or other qualified service organization, always using
identical replacement parts.
Checking the Lower Guard (Fig. A)
1. Turn tool off and disconnect from power supply.
2. Rotate the lower guard lever (Fig. A,
position to the fully open position.
3. Release the lever and observe the guard
fully closed position.
The tool should be serviced by a qualified service center if it:
• fails to return to the fully closed position,
• moves intermittently or slowly, or
EnGLIsH
8 , depress the blade
8 and outer clamp
6 ) from the fully closed
7 return to the
43