Working Advice; Maintenance And Cleaning - Würth TBS 12-A Traducción Del Manual De Instrucciones De Servicio Original

OBJ_BUCH-2872-001.book Page 16 Monday, July 4, 2016 12:17 PM
Light pressure on the On/Off switch 10 results in a low rota-
tional speed. Further pressure on the switch results in an
increase in speed.
Adjusting the Screw-in Depth
(see figure B)
With the adjustment sleeve 3, the screw-in depth of the screw
head into the workpiece can be preset in 8 locking steps per
full turn. Each step corresponds with a 0.25 mm change of the
screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction results
in a greater screw-in depth; turning in anticlockwise direction
reduces the screw-in depth.
The required setting is best determined by testing.
Temperature Dependent Overload Pro-
tection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the power output is
reduced or the power tool is switched off. The power tool will
not run at full power output again until the permitted battery
temperature has been reached.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.

Working Advice

 Apply the power tool to the screw only when
it is switched off. Rotating tool inserts can slip off.
Guide the screw toward the screwdriving bit 1. The screw is
held in place by the magnet pull of the universal bit holder 11.
Firmly push the tip of the screw into the material to be screwed
until the screwing-depth stop 4 faces against the workpiece.
Switch the machine on. The screw is screwed into the material
until the adjusted screw-in depth is reached. The drive is disen-
gaged and the tool holder no longer rotates. Check the screw-
in depth and readjust, if required.
For unscrewing screws, set the rotational direction switch 5 to
left rotation and pull off the screwing-depth stop 4 toward the
front without turning the adjustment sleeve.
Working with the screwing-depth stop 4 is also possible when
adapting the screw-in depth.

Maintenance and Cleaning

 Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as dur-
ing transport and storage, remove the battery
from the power tool. There is danger of injury when
unintentionally actuating the On/Off switch.
 For safe and proper working, always keep the
machine and ventilation slots clean.
To ensure trouble-free operation of the power tool, clean the
mount of the universal bit holder 11 and the screwing-depth
stop 4 with compressed air at regular intervals.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
a Würth master-Service.
In all correspondence and spare parts orders, please always
include the article number given on the type plate of the
machine.
The current spare parts list for this power tool can be viewed
on the internet at http://www.wuerth.com/partsmanager or
be requested from your next Würth branch office.
Guarantee
For this Würth power tool, we provide a guarantee in accord-
ance with the legal/country-specific regulations from the date
of purchase (verified by invoice or delivery document). Dam-
age that has occurred will be corrected by replacement or
repair.
Damage caused by normal wear, overloading or improper
handling is excluded from the guarantee.
Claims can only be accepted if the power tool is sent undisas-
sembled to a Würth branch office, your Würth sales repre-
sentative or a customer service agent for Würth power tools.
Transport
The contained lithium-ion batteries are subject to the Danger-
ous Goods Legislation requirements. The user can transport
the batteries by road without further requirements.
When being transported by third parties (e.g.: air transport or
forwarding agency), special requirements on packaging and
labelling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is
required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery in
such a manner that it cannot move around in the packaging.
Please also observe possibly more detailed national regula-
tions.
16