Volvo Penta 2002 Instrucciones De Montaje página 4

Installation
The generator should be connected to a separate
battery (batteries) as per the wiring diagram
(Fig. 2).
The total width of the engine increases by 15 cm
on the left side. The generator bracket can also be
installed if the cooler compressor bracket is instal-
led. With the generator bracket installed the engine
cannot be started with the manual start.
The set 828944 includes:
Pos Fig 1 and 4
1 Bracket
2 Spacer washer 2 mm
3 Screw M10x30
4 Screw M10x60
5 Lock nut M10
6 Clamp iron
7 Screw M8 x 30
8 Spring washer 8.5
9 Nut M8
10 Generator A13N
11 Screw M8x120
12 Lock nut M8
13 V-belt HC50 x 1000
14 Screw M8x40
15 Washer 8.4x22x2
16 Lock nut M8
17 Pulley, gen.
18 Sleeve washer
21 Pulley
22 Spacer ring
23 Screw M8 x 50
24 Spring washer
Pos Fig. 2
1 Relay
2 Cable harness 8 m
3 Round cable terminal M5
4 Nut M5
5 Spring washer 5.3
6 Round cable terminal M6
7 Nut M6
8 Spring washer 6.7
9 Protective cap (rubber)
10 Lamp socket
11 Lamp
12 Spring nut
13 Rubber ring
14 Lamp socket holder
15 Symbol plate
Tie
Assembly instructions
1. Loosen the two front screws for the front left
2. Install the bracket (1) under the fuel filter at-
3. Install the pulley (17) on the generator. Torque
Quantity
1
1
2
2
4. Put the sleeves washers (18) in position and in-
2
1
1
5. Install the additional pulley as per Fig. 4.
1
6. Put on the V-belt and check the tension as per
1
1
1
7. Install the relay (1 Fig 2) on one of the screws
1
1
2
1
1
8. Determine the location of the indicator lamp,
2
1
1
4
4
9. Fit the lamp socket holder, 14. (lock with the
Quantity
1
1
1
10. Connect the cables as shown in fig. 2. Hang up
1
1
1
1
1
2
1
1
11. Check that the charging warning lamp goes out
1
1
1
1
10
1
engine fixture. Loosen also the two screws for
the fuel filter. To gain access to the screws the
sray pipe must be loosened and bent out of the
way (carefully) and then retightened.
tachment bridge (on the top cover) and to the
engine fixture (NOTE! spacer 2). Use the set
screws. Tighten the fuel filter in the top cover
(use the existing washer, 25) and secure the
generator bracket underneath with the nuts (5).
45–60 Nm (4.5–.0 kpm). Hold the nut with a 24
mm block wrench and tension the axle with an
8 mm socket head wrench.
stall the generator as per Fig. 1.
Fig. 3.
for the voltmeter's attachment clip (large board
A) and the rev counter's attachment clip (small
board B).
also check that there is room at the rear of the
panel. Then drill a Ø 12 mm hole.
rubber ring, 13 and spring nut, 12). Fit the lamp
and lamp socket and also attach the symbol
plate.
the cable harness with the ties. The
cross-section of the battery cables in relation
to their total length is shown in the table. Ca-
bles and battery connections are not included
in the kit.
once the engine has started.