Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-1627-003.book Page 16 Monday, June 20, 2016 12:10 PM
Tool Specifications
Sabre saw
Art. No.
Rated voltage
Stroke rate at no load n
0
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
– during operation* and
during storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-11:
2
Cutting board: a
=8.0 m/s
, K=1.5 m/s
h
Cutting wooden beam: a
=12.0 m/s
h
The values given for sawing particle board apply for a workpiece thick-
ness of 20 mm.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools or
is poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
SBS 12-A
accessories, keep the hands warm, organisation of work pat-
5700 112 X
terns.
V=
12
-1
min
0–3000
mm
14.5
mm
65
We declare under our sole responsibility that the product
mm
8
described under "Tool Specifications" complies with all
mm
50
applicable provisions of the directives 2009/125/EC
(Regulation 1194/2012), 2011/65/EU, 2014/30/EU,
kg
1.2–1.4
2006/42/EC including their amendments and is in conform-
ity with the following standards: EN 60745-1,
°C
0...+45
EN 60745-2-11, EN 50581.
Technical file (2006/42/EC) at:
°C
–20...+50
Adolf Würth GmbH & Co. KG, Abt. PPT
AKKU-LI 12 V/ x,x Ah
Reinhold-Würth-Straße 12–17
AL 30-LI
74653 Künzelsau
GERMANY
Frank Wolpert
General Manager
Künzelsau: 01.08.2016
Use only the chargers listed in the tool specifi-
2
,
2
2
, K=1.5 m/s
.
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch
Observe the notes for disposal.
EC-Declaration of Conformity
Dr.-Ing. Siegfried Beichter
General Manager
Battery Charging
cations. Only these chargers are matched to the lithium-
ion battery of your power tool.
after the machine has been automatically
switched off. The battery can be damaged.
16
Tabla de contenido
