Dräger X-plore 8000 Instrucciones De Uso página 18

en |
Transport
5.2.8 Replace the protective foil
Only applies to X-plore 8000 helmet with visor.
1. Detach the outer visor frame from the inner visor frame
(see fold-out page, Fig. D).
2. Remove the old protective foil and adhesive strip.
3. If necessary, wipe the visor shield with a damp cloth and
dry with a soft cloth.
4. Center the protective foil on the inner visor frame and stick
it to the visor shield.
5. Press the outer visor frame onto the inner visor frame.
Make sure that the protective foil slides under the outer
visor frame.
6. Click the outer visor frame into the inner visor frame. The
two visor frames must sit flush with each other.
5.2.9 Replace the chin trim
Only applies to X-plore 8000 helmet with visor.
1. Detach the chin trim flaps from the headband (see fold-out
page, Fig. M).
2. Loosen the screws on the fixed visor frame (see fold-out
page, Fig. J) and remove the chin trim from the helmet.
3. Secure the new chin trim to the fixed visor frame using the
screws (see fold-out page, Fig. J). Tighten the screws by
hand.
4. Press the chin trim into the groove of the visor frame.
5. Hook the chin trim flaps onto the headband (see fold-out
page, Fig. M).
5.2.10 Replace neck trim or shoulder trim
Only applies to X-plore 8000 helmet with visor.
1. Detach the hook-and-loop straps and clips in the helmet
trim from the helmet (see fold-out page, Fig. L and N).
2. Loosen the screws on the fixed visor frame (see fold-out
page, Fig. J) and remove the helmet trim from the helmet.
3. Center the rear seam of the new helmet trim to the hose
connection.
4. Open the visor.
5. Press the helmet trim into the groove of the helmet and
visor frame. The clips must click into place on the helmet
(see fold-out page, Fig. N).
6. Secure the helmet trim to the fixed visor frame using the
screws (see fold-out page, Fig. J). Tighten the screws by
hand.
7. Pull the hook-and-loop straps of the helmet trim through
the eyelets in the helmet and close them (see fold-out
page, Fig. L).
18
5.2.11 Replace the visor frame
Only applies to X-plore 8000 helmet with visor.
1. Loosen the screws of the pivot plates in the helmet and
remove them with the fastening elements (see fold-out
page, Fig. K).
2. Remove the threaded plug with spring and blind plug on
the outside from the helmet shell.
3. Remove the visor frame.
4. If necessary, replace the sealing in the fixed frame.
5. Place the new visor frame on the helmet shell.
6. Place the spring on the threaded plug and use it to fix the
visor frame on both sides.
7. Fit the fastening elements and screws. Tighten the screws
by hand.
8. Insert the visor shield.
5.2.12 Replace the visor sealing
Only applies to X-plore 8000 helmet with visor.
1. Pull the sealing out of the fixed visor frame.
2. Starting at one end, press the new sealing into the groove
of the visor frame.
5.2.13 Replace the visor shield
Only applies to X-plore 8000 helmet with visor.
1. Open the visor.
2. Detach the outer visor frame from the inner visor frame
(see fold-out page, Fig. D).
3. Remove the visor shield from the inner visor frame.
4. Insert the new visor shield into the inner visor frame (see
fold-out page, Fig. I) and fix it to the outer visor frame.
5. Click the outer visor frame into the inner visor frame. The
two visor frames must sit flush with each other.
6 Transport
Transport the facepiece in its original packaging.
7 Storage
Store Dräger X-plore 8000 helmets with visor fully assembled
in their original packaging. Dräger X-plore 8000 helmet/hood
combinations and Dräger X-plore 8000 bump cap/hood
combinations can be hung by the hood flap or stored in their
original packaging.
Keep all facepieces dry and free of dirt, protect from direct
sunlight and thermal radiation. Avoid storing near aggressive
substances (such as solvents and fuels).
Instructions for use |
Dräger X-plore 8000 Facepieces