Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NEVER
IMMEDIATELY AFTER USE AS IT IS VERY HOT AND MAY BURN YOUR
SKIN.
PRESENT POTENTIAL DANGERS!
DO
PROPYLENE LINE!
•
POLYPROPYLENE AND POLYETHYLENE LINES ARE DANGEROUS
FOR PULLING DUE TO THEIR ELASTICITY AND THEIR LOW
MELTING POINT.
•
MAKE SURE THAT THE LINE IS NOT DAMAGED AND OFFERS
ADEQUATE RESISTANCE FOR THE LOAD TO BE PULLED.
STRETCHING = DANGER!
•
STRETCHING THE LINE MAY CAUSE SERIOUS INJURY
CAREFUL WHEN RELEASING THE TENSION IN THE LINE
:
•
ALL LINES STRETCH
INCREASED LENGTH: THE MORE THE LINE
IS PULLED, THE MORE IT STRETCHES.
•
STRETCHING THE LINE MAY CAUSE THE LOAD TO MOVE IN AN
UNEXPECTED AND DANGEROUS MANNER
•
STRETCHING THE LINE MAY CAUSE IT TO RELAX AND MOVE
,
BACKWARDS QUICKLY
WINCH OR CAUSING SEVERE BURNS
•
NEVER WIND THE LINE AROUND YOUR HAND.
PERFORM A VISUAL INSPECTION OF THE
LINE BEFORE EACH USE. IF IT PRESENTS OBVIOUS SIGNS OF WEAR
(CHOPPED STRAINS, EXCESSIVE ABRASION), CHANGE IT.
IF YOUR LINE IS DIRTY, CLEAN IT. A DIRTY
LINE CAN QUICKLY BECOME DAMAGED AND CAUSE PREMATURE
WEAR TO THE PARTS IN CONTACT WITH IT.
WHAT NOT TO DO:
WHEN YOU INSTALL THE SLING TO ANCHOR THE WINCH, AVOID A
FULL TURN AROUND AN ANCHORING POINT. THIS WILL PREVENT
THE WINCH FROM ALIGNING ITSELF WITH THE LOAD CORRECTLY.
THIS WILL ALSO APPLY UNEVEN TENSION TO EACH OF THE HOOKS.
AVOID INSTALLING THE SLING ON SHARP
CORNERS LIKELY TO DAMAGE THE POLYESTER SLING. WHEN YOU
USE A POLE, A TREE OR A STUMP AS AN ANCHORING POINT,
INSTALL THE SLING CLOSE TO THE BASE.
ANCHORING AROUND A STUMP REQUIRES
SPECIAL ATTENTION TO AVOID THE SLING SLIPPING OFF THE TOP
OF THE STUMP.
MAKE SURE THAT THE ANCHORING POINT
IS ABLE TO RESIST THE PULLING WITHOUT BREAKING, BEING
UPROOTED
OR
TOUCH
THE
CAPSTAN
MOST
PULLING
SITUATIONS
NOT
USE
A
3-STRAND
.
.
PULLING YOUR HAND TOWARDS THE
.
BECOMING
DAMAGED.
DRUM
HANDS OR YOUR BODY! ALSO BEWARE OF THE BUILT-UP TENSION
CLOSE TO YOU AND MAKE SURE THAT YOU ARE A SAFE DISTANCE
FROM THIS ACCUMULATION.
DURING OPERATION AND MAKE SURE THAT THE LINE DOES NOT
CROSS THE LATTER. IF THIS OCCURS, RELEASE THE TENSION IN
YELLOW
THE LINE, STOP THE ENGINE AND REMOVE THE KINK.
LOAD DOESN'T MOVE (OFTEN WHEN A VERY LONG LINE IS USED),
THIS MEANS THAT YOUR LINE IS STRETCHED AND THE BREAKING
POINT COULD QUICKLY BE REACHED AND THE LOAD CAN SUDDENLY
BE HEADING TOWARDS YOU. SLOWLY RELEASE THE TENSION IN
THE LINE BUT BEWARE OF THE BUILT-UP TENSION: THE LINE MAY
QUICKLY GET AWAY FROM YOU CAUSING BURNS OR TAKING YOU
TOWARDS THE WINCH.
.
BE
THE HOOKS, THE LINE AND THE POLYESTER SLING TO DETECT ANY
DAMAGE OR SIGNS OF WEAR.
2.0 Checks before use
2.1 When receiving the winch
Inspect the box to detect any obvious damage. If a part is
missing or damaged, notify the carrier immediately.
2.2 Battery
THE TIME OF PURCHASE. BEFORE USING YOUR PORTABLE CAPSTAN
FOR THE FIRST TIME, FOLLOW ALL THE INSTRUCTIONS AND
TM
WINCH
GUIDELINES INDICATED IN THE BATTERY AND CHARGER SUPPLIER
GUIDES. REMOVE THE BATTERY BEFORE STORING THE PORTABLE
CAPSTAN WINCH
PORTABLE CAPSTAN WINCH
FOR AT LEAST ONE COMPLETE CHARGING PERIOD. THIS BATTERY
INCLUDES NO MEMORY EFFECT.
2.3 Installing the battery's protective cover.
This cover is designed to protect 4.0 - 5.0Ah batteries located
outside
The cover is supplied with a spring and a short metal rod.
a building:
A) Place the spring in the housing cavity and then the pin.
B) Place the lid in the other cavity and push the pin against
the spring.
C) Position the cover holding the pin until it snaps into the
housing.
NEVER WIND THE LINE AROUND YOUR
KEEP AN EYE ON THE CAPSTAN DRUM
IF THE WINCH PULLS THE LINE AND THE
DURING CLEANING, INSPECT THE WINCH,
THE BATTERY IS ONLY HALF-CHARGED AT
FOR A LONG PERIOD. BEFORE REUSING THE
TM
AGAIN, CHARGE THE BATTERY AGAIN
TM
the
housing
Perform the following operation inside
EN
from
rain.
Tabla de contenido
