Tabla de contenido
Idiomas disponibles
Idiomas disponibles
KF 5 EBQ
GB
Turn the adjusting screw [5-4] in the plastic part
of the guide.
Clamp the guide rods with the rotating knobs
[5-5] in the precision adjustment.
Loosen the rotating knobs [5-3] of the parallel
guide.
Set the desired distance with the adjusting
screw and retighten the rotating knobs.
11.2
Routing with the FS guide system
The guide system, available as an accessory, facili-
tates routing straight grooves.
Fasten the guide stop [6-1] to the platen with
the guide rails [5-6] of the parallel guide.
Fasten the guide rail [6-3] with FSZ screw
clamps [6-4] to the workpiece.
Make sure that the safety distance X - Fig. [6] of
5 mm between the front edge of the guide rail
and cutter or groove is observed.
Place the guide stop onto the guide rail as
shown in Fig. [6] To ensure a backlashfree guid-
ance of the router stop you can adjust two guide
cheeks with a screwdriver through the side
openings [6-2].
Screw the height-adjustable support [6-5] of
the router table's threaded bore in such a way
that the underside of the router table is parallel
to the surface of the workpiece.
12
Environment
Do not throw the power tool in your household
waste! Dispose of machines, accessories and pack-
aging at an environmentally responsible recycling
centre. Observe the valid national regulations.
EU only: European Directive 2002/96/EC stipulates
that used electric power tools must be collected
separately and disposed of at an environmentally
responsible recycling centre.
13
Warranty
We offer a warranty for material and production de-
fects for all our tools in accordance with the locally
applicable legal provisions, but for a minimum of 12
months. Within the EU member states, the warran-
ty period is 24 months (verification through invoice
or delivery note). Damage caused by the operator,
natural wear, overloading, incorrect handling or
through the use of the equipment not specified in
the operating manual, or damage which was known
16
at the time of purchase, is not covered by the war-
ranty. Furthermore, damage caused by the use of
non-original accessories and consumable materi-
als (e.g. sanding pads) is also excluded.
Complaints can only be accepted if the tool is re-
turned while still assembled to the supplier or an
authorised Festool Customer Service workshop.
Keep the operating manual, safety instructions,
spare parts list and purchase receipt in a safe
place. Otherwise the current warranty conditions of
the manufacturer shall apply.
Note
Due to continuous research and development work,
we reserve the right to make changes to the techni-
cal content of this documentation.
14
EU Declaration of Conformity
Putty Cutter
KF 5 EBQ
Year of CE mark: 2006
We declare under sole responsibility that this prod-
uct complies with the following directives and stan-
dards:
2006/42/EG, 2004/108/EG, 2011/65/EU, EN 60745-
1, EN 60745-2-17, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3.
Festool Group GmbH & Co. KG
Wertstr. 20, D-73240 Wendlingen, Germany
Dr. Martin Zimmer
Head of Research, Development and Technical
Documentation
19.12.2012
REACh for Festool products, its accessories and
consumable materials:
REACh is a European Chemical Directive that came
into effect in 2007. As "downstream users" and
product manufacturers, we are aware of our duty to
provide our customers with information. We have
set up the following website to keep you updated
with all the latest news and provide you with infor-
mation on all the materials used in our existing
products:
www.festool.com/reach
Serial No.
494101
Capítulos
Tabla de contenido
