Skil F0157350 Serie Manual De Instrucciones página 6

SAFETY INSTRUCTIONS FOR SANDERS
Avoid damage that can be caused by screws, nails and
●
other elements in your workpiece; remove them before
you start working
Always keep the cord away from moving parts of the
●
tool; direct the cord to the rear away from the tool
When you put away the tool, switch off the motor and
●
ensure that all moving parts have come to a complete
standstill
Use completely unrolled and safe extension cords with a
●
capacity of 16 Amps (U.K. 13 Amps)
In case of electrical or mechanical malfunction,
●
immediately switch off the tool and disconnect the plug
SKIL can assure flawless functioning of the tool only
●
when original accessories are used
This tool should not be used by people under the age of
●
16 years
The noise level when working can exceed 85 dB(A);
●
wear ear protection
If the cord is damaged or cut through while working, do
●
not touch the cord, but immediately disconnect the plug
Never use tool when cord is damaged; have it replaced
●
by a qualified person
Always check that the supply voltage is the same as the
●
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
This tool is not suitable for wet sanding
●
Do not work materials containing asbestos (asbestos
●
is considered carcinogenic)
When sanding metal, sparks are generated; do not use
●
dustbox and keep other persons and combustible
material from work area
Do not touch the moving sanding sheet
●
Do not continue to use worn, torn or heavily clogged
●
sanding sheets
Wear protective gloves, safety glasses, close-fitting
●
clothes and hair protection (for long hair)
Take protective measures when during work dust
●
can develop that is harmful to one's health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/chip
extraction when connectable
Always disconnect plug from power source before
●
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
●
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
●
tool, it must be disposed of safely and not left
unattended
TOOL ELEMENTS 2
A Dust box
B Pressure control (7365)
C On/off switch
D Sanding speed selection wheel (7360)
USE
Mounting of sanding sheet
●
7350/7360/7365 3
7360/7365 4
! disconnect the plug
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot 3
! replace worn sanding sheets in time
! always use the tool with the total sanding surface
covered with sanding paper
Dust suction 5
●
- empty dustbox A regularly for optimal dust pick-up
performance
! do not use dustbox when sanding metal
Pressure control (7365) 6
●
Warns the user when applying too much pressure on the
tool while working (too much pressure reduces the
sanding performance)
- green light 1 turns on when running tool is placed on
workpiece
- green light 2 turns on in case of pressure
- green light 3 turns on in case of increased pressure
- red light 4 turns on when pressure is too high
On/off switch
●
- switch on/off the tool by pushing switch C 2
forward/backwards
! before the sanding surface reaches the
workpiece, you should switch on the tool
! before switching off the tool, you should lift it
from the workpiece
VariTronic speed control (7360)
●
For optimal sanding results on different materials
- with wheel D 2 you can set the desired sanding
speed
- adjust speed to grit size used
- before starting a job, find the optimal speed and grit
by testing out on spare material
Holding and guiding the tool 7
●
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep the ventilation slots uncovered
APPLICATION ADVICE
Move the tool in straight movements in line with the
●
grain
- for sanding bare wood surfaces
- for extra fine finishing
Never use the same sanding sheet for wood and metal
●
When cord needs to be replaced, first remove foot-plate
●
as illustrated 8
6