Prior To Operation - DeWalt DCS391 Traducido De Las Instrucciones Originales

EngLIsh
4. Thread on the blade clamping screw
washer in position. Turn anti-clockwise.
5. Press the blade lock button
until the blade stops rotating.
6. Tighten the blade clamping screw firmly using the hex key.
Blades

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle material.
Foreign objects in the workpiece such as wire or nails
can cause tips to crack or break. Only operate saw when
proper saw blade guard is in place. Mount blade securely
in proper rotation before using, and always use a clean,
sharp blade.

WARNING: Do not cut ferrous metals (steel), masonry,
glass, masonry-type planking, cement board or tile with
this saw.
Do not use abrasive wheels or blades. A dull blade will cause
slow inefficient cutting, overload on the saw motor, excessive
splintering, and could increase the possibility of kickback.
If you need assistance regarding blades, please call contact your
local service center listed on the back of the manual.

Prior to Operation

• Make sure your battery pack is (fully) charged.
• Make sure the guards have been mounted correctly. The saw
blade guard must be in closed position.
• Make sure the saw blade rotates in the direction of the arrow
on the blade.
• Do not use excessively worn saw blades.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Always wear proper personal hearing
protection. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.

WARNING:
• Ensure the material to be sawn is secured in place.
• Apply only a gentle pressure to the tool and do not
exert side pressure on the saw blade. If possible, work
with the saw shoe pressed against the workpiece. This
prevents damage to the blade and stops the tool from
jerking and vibrating.
• Avoid overloading.
• Let the blade run freely for a few seconds before starting the cut.
38
8 by hand to hold the
11 while turning the spindle
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Hold the tool by the main grip
to guide the saw properly.
Switching On and Off (Fig. A)
For safety reasons the trigger switch
with a lock-off button 1 .
Press the lock-off button to unlock the tool.
To run the tool, press the trigger switch
trigger switch is released the lock-off switch is automatically
activated to prevent unintended starting of the machine.
NOTICE: Do not switch the tool ON or OFF when the saw
blade touches the workpiece or other materials.
Guiding the Tool (Fig. A)
• For optimum results, clamp the workpiece bottom up.
• Use the kerf indicator 9 to follow the line drawn on the
workpiece. The kerf indicator lines up with the left side of
the saw blade when set to 50° bevel. The kerf indicator lines
up with the right side of the saw blade when set to 0° bevel.
Dust Extraction (Fig. I)
QW, XJ, GB
A dust extraction port 21 is supplied with your tool.
• Always use a vacuum extractor designed in compliance with
the applicable Directives regarding dust emission when
sawing wood. Vacuum hoses of most common vacuum
cleaners will fit directly into the dust extraction spout.
To Install Dust Extraction Port (Fig. I)
1. Fully loosen depth adjustment lever
2. Place shoe 5 in the lowest position.
3. Align dust extraction port
shoe as shown.
4. Align tab on the dust extraction port with the threaded hole
on the bracket.
5. Insert screw and tighten securely.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
20 and the auxiliary handle 12
2 of your tool is equipped
2 . As soon as the
4 .
21 against the bracket on the