Tool Change With Sds Chuck; Maintenance / Cleaning; Environmental Protection; Technical Specifications - Metabo PowerMaxx BH 12 BL 16 Manual Original

en ENGLISH
L = anti-clockwise rotation (for the removal of
screws)
0 = Centre position: with the transporting safety
device engaged (switch-on lock)
7.5

Tool change with SDS chuck

Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting tools:
- Turn tool and insert until it engages. The tool is
locked automatically.
Removing the tool:
See page 2, fig. A.
- Pull tool lock (1) backwards in direction indicated
by arrow (a) and remove tool (b).
7.6 Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to the
handle when pushing down the machine and do not
force. Vibrations are reduced most effectively at the
central position (5).
8. Maintenance, cleaning
- Ventilation slits:
Clean the ventilation slits on the machine occa-
sionally.
- Remove the battery pack periodically and wipe
the contact area of the battery pack and machine
with a dry cloth and remove drilling dust.
f 9. Troubleshooting
Metabo S-automatic safety stop: The LED light
(11) lights up and the machine SWITCHES OFF
automatically. If the speed is too high (if the
machine seizes suddenly), the machine switches
off. Switch off the machine at the trigger switch (7).
Switch it on again and continue to work as normal.
Try to prevent the machine from seizing.
f
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Batter chargers: ASC 55, ASC 30-36, etc.
Battery packs with different capacities. Only
use battery packs with voltage suitable for your
power tool.
10
Order no.:
625406000 ............... 12 V 2.0 Ah (LiPower)
625349000 ............... 12 V 4.0 Ah (LiHD)
etc.
625596000 ............... 18 V 2.0 Ah (LiPower)
625367000 ............... 18 V 4.0 Ah (LiHD)
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
11. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

12. Environmental Protection

Do not allow battery packs to come into contact with
water!
To protect the environment, do not dispose of
power tools or battery packs in household
waste. Observe national regulations on
separated collection and recycling of disused
machines, packaging and accessories.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).
f

13. Technical Specifications

Explanation of details on page 3. Subject to
changes serving technical progress.
U = Voltage of battery pack
n = No-load speed
0
n = Load speed
1
dia. = Maximum drill diameter
max
s = Maximum impact rate
max
W = Single impact force
m = Weight with smallest battery pack
D = D=Collar diameter
Measured values determined in conformity with EN
60745.
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.