Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OPERATION
The hood is operated using the push buttons on the front panel.
Lamp
Speed
1
2
) 1
T
m i
e
D /
l e
y a
p
u
h s
b
t u
o t
n
) 2
L
g i
h
n i t
g
p
u
h s
b
t u
o t
n
TIME/DELAY (2 Functions)
TIME SETTING
This button is used to set time when lighting and blower are not
in use. Time is displayed in a 12-hour cycle. To set time, press
the push button (1) for 3 seconds. The first two digits will flash.
Use the blower push button (3) to increase, and the lighting
pushbutton (2) to decrease. Press the time/delay push button (1)
again. The last two digits will flash. Use the blower push button
(3) to increase and the lighting push button (2) to decrease.
Press the time/delay button (1) again to confirm and exit time
setting mode.
DELAY SETTING
When blower is in use, this button is used as the delay off setting
button. To set delay, press the push button (1). The delay is
factory set at 5 minutes, but can be set from 1 up to 60 minutes.
Use blower push button (3) to increase, and lighting push button
(2) to decrease. Countdown will be displayed on the LCD screen,
blower symbol will be activated, and the button (1) backlight
will flash. Blower will continue to operate for the programmed
time and then will stop automatically (delay-off setting does
not affect lighting as it works independently). To cancel delay
function, press time/delay push button (1) again. The blower will
continue to operate and won't stop until ON/OFF push button (4)
is pressed. To turn delay function and blower OFF at once, press
ON/OFF push button (4). NOTE: Delay will be reset if blower
speed is modified during delay setting mode.
LIGHTING
Press the lighting push button (2) once to turn the LCD screen
on. To turn the lights on, press the lighting push button (2) once
more. Press it again to turn the lights OFF. The LCD screen will
turn off automatically after 15 seconds of inactivity (blower and/
or lights).
BLOWER
The blower push button (3) turns the blower on to one of three
speed settings: LOW, MEDIUM or HIGH. Press the blower (3) or
ON/OFF (4) push button once to turn the LCD screen on. Press
the blower (3) or ON/OFF (4) push button once more to turn
the blower on at the last selected speed. Blower symbol will be
activated. To change the blower speed, press the blower push
button (3) until the desired speed is obtained. Press the ON/OFF
push button (4) to turn the blower OFF. The last speed used will
be memorized. NOTE: When blower is turned on, 100% of power
level is activated for 1 to 2 seconds. It will then operate at the
previous setting.
Timer
Power
3
4
) 3
B
o l
w
r e
p
u
h s
b
t u
o t
n
) 4
O
N
O /
F
F
p
u
h s
b
t u
o t
n
CLEANING & MAINTENANCE
Proper maintenance of the Range Hood will assure proper performance
of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If the motor
bearings make excessive or unusual noise, replace the motor with the
exact service motor. The impeller should also be replaced.
GREASE FILTER
The grease filter should be cleaned frequently. Use a warm dishwashing
detergent solution. Grease filter is dishwasher safe.
Clean all-metal filters in the dishwasher using a non-phosphate deter-
gent. Discoloration of the filter may occur if using phosphate detergents,
or as a result of local water conditions - but this will not affect filter perfor-
mance. This discoloration is not covered by the warranty.
Remove grease filter by pulling down on the metal latch tab. This will
disengage the filter from the hood. Tilt the filter downward and remove.
NON-DUCTED RECIRCULATION FILTER
The non-ducted recirculation filter should be changed every 6 months.
Replace more often if your cooking style generates extra grease, such
as frying and wok cooking. Turn the filter mounting tabs to remove filter
and replace.
STAINLESS STEEL CLEANING
DO:
• Regularly wash with clean cloth or rag soaked with warm water and
mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning. Wipe
dry completely.
• You may also use a specialized household stainless steel cleaner.
DON'T:
• Use any steel or stainless steel wool or any other scrapers to remove
stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the hood.
During construction/renovation, cover the range hood to make sure no
dust sticks to the stainless steel surface.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel
• Any products containing: chloride, fluoride, iodide, bromide will deterio-
rate surfaces rapidly.
• Any combustible products used for cleaning such as acetone, alco-
hol, ether, benzol, etc., are highly explosive and should never be used
close to a range.
LIGHT BULBS
!
CAUTION:
bulbs to cool down before removing them.
This range hood requires two incandescent bulbs (Type B10,
120V, 40W Max, candelabra).
To install or change bulbs:
1. Remove grease filter by pulling down the metal latch and
tilting filter down.
2. If non-duct filter is installed, remove filter by turning filter
mounting tabs.
3. Remove and discard bulb. Replace with new bulb.
4. Re-install non-duct filter (if applicable).
5. Re-install grease filter.
NS54000 SERIES
Bulbs may be hot. Always allow
Page 2
Tabla de contenido
