Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OPERATION
The hood is operated using the push buttons on the front panel.
BLOWER ON
& SPEED
INCREASE
BLOWER
SPEED
DECREASE
& OFF
LIGHTS
Push the
button to turn the lights ON and OFF.
BLOWER
Push the
button once to turn blower ON to LOW SPEED.
Blower symbol will be illuminated. When blower is initially turned
on, it will start on HIGH SPEED for 1 second, then return to LOW
SPEED. To increase the blower speed, push the
the desired speed is obtained. When highest speed setting is
selected, the
button will not be illuminated.
Push the
button to decrease the blower speed until the
desired speed is obtained. Continue to push the
turn blower OFF.
BLOWER DELAY
When blower is ON, push the
10-minute delay off. Delay symbol will flash on/off once activated.
Blower will continue to operate for 10 minutes and then will stop
automatically. (Delay off setting does not affect lighting.)
To cancel delay function, push
continue to operate and will not stop until turned off using the
button.
Note: Delay will be reset if blower speed is modified during delay
setting mode.
BLOWER
DELAY
OFF
LIGHTS
ON / OFF
button until
button to
button to activate the
button again. The blower will
CLEANING & MAINTENANCE
Proper maintenance of the Range Hood will assure proper performance
of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If the motor
bearings make excessive or unusual noise, replace the motor with the
exact service motor. The impeller should also be replaced.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm dishwashing
detergent solution. Grease filters are dishwasher safe.
Clean all-metal filters in the dishwasher using a non-phosphate deter-
gent. Discoloration of the filters may occur if using phosphate detergents,
or as a result of local water conditions - but this will not affect filter perfor-
mance. This discoloration is not covered by the warranty.
Remove grease filters by pulling down on the metal latch tab. This will
disengage the filter from the hood. Tilt the filter downward and remove.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every 6 months.
Replace more often if your cooking style generates extra grease, such
as frying and wok cooking. Turn the filter mounting tabs to remove filter
and replace.
STAINLESS STEEL CLEANING
DO:
• Regularly wash with clean cloth or rag soaked with warm water and
mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning. Wipe
dry completely.
• You may also use a specialized household stainless steel cleaner.
DON'T:
• Use any steel or stainless steel wool or any other scrapers to remove
stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the hood.
During construction/renovation, cover the range hood to make sure no
dust sticks to the stainless steel surface.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel
• Any products containing: chloride, fluoride, iodide, bromide will deterio-
rate surfaces rapidly.
• Any combustible products used for cleaning such as acetone, alco-
hol, ether, benzol, etc., are highly explosive and should never be used
close to a range.
LIGHT BULBS
!
CAUTION:
bulbs to cool down before removing them.
This range hood includes two incandescent bulbs (Type B10,
120V, 40W Max, candelabra).
To install or change bulbs:
1. Remove grease filter(s) by pulling down the metal latch
and tilting filter down.
2. Remove and discard bulb. Replace with new bulb.
3. Re-install grease filter(s).
NS58000 SERIES
Bulbs may be hot. Always allow
Page 2
Tabla de contenido
