Components And Controls - Pulsar AXION LRF XQ38 Manual De Instrucciones

COMPONENTS AND CONTROLS

Eyepiece focus ring
1.
DOWN/LRF button
2.
MENU button
3.
UP/ZOOM button
4.
Power ON/CALIBRATION button
5.
Lens focus ring
6.
Lens cover
7.
Tripod adapter
8.
USB Type-C connector
9.
Laser rangefinder
10.
LED indicator displays the current status of the device:
LED Indicator
Operating Mode
Device is turned on
The device is turned on/battery charge < 10%
BUTTONS OPERATION
Button Operating Mode
Device is turned off
Button
Display is turned off
ON/OFF
Device is turned on,
quick menu, main
(5)
menu
Button Device is turned on
Quick menu
UP/ZOOM
Main menu
(4)
Device is turned on
Button
Quick menu
MENU
Main menu
(3)
Device is turned on
The device is on, the
Button rangefinder is on
DOWN/ LRF
The device is on,
(2) the rangefinder is in
scanning mode
Quick menu
Main menu
BATTERY PACK CHARGING
The AXION LRF XQ thermal imager comes with an APS 5 rechargeable Lithium-ion battery. APS 5 batteries
support USB Power Delivery fast charging technology when using a standard charging set (charger, USB Type-C
cable, power adapter). Before first use, make sure the battery is fully charged.
USER MANUAL FOR AXION LRF XQ38 THERMAL IMAGING SCOPE
First short press Subsequent short Long press
presses
Turn device on Device calibration Turn device on
Turn display on Device calibration Turn device off
Device calibration Turn display off / Turn
device off
Toggle between observation modes Zoom
Increase value Increase value
Navigate up / right Navigate up / right
Access quick menu Enter main menu
Switch between quick menu options Exit quick menu
Confirm selection, enter menu items Exit menu items, main
menu
Turn on rangefinder Single distance Quick change of color
measurement palettes
Single distance measurement Activate rangefinder
scan mode
Deactivate rangefinder scan mode Turn off rangefinder
Decrease value Decrease value
Navigation down / left Navigation down / left
Option 1
•
Install the APS 5 battery (11) in the battery compartment (19) of the device.
• Connect the USB cable (16) to the USB Type-C connector (9) of the device.
•
Connect the other end of the USB cable (16) to the Power Adapter (15).
•
Plug the Power Adapter (15) into a 100-240 V socket (17).
Option 2
•
Insert the APS 5 battery (11) along the guide into the APS 5 charger (12) slot as far as it
will go (see Fig.). The APS charger is supplied with your device and sold separately.
•
Connect the plug of the USB Type-C cable (16) to the USB Type-C connector of the Power
Adapter (15).
•
Plug the Power Adapter (15) into a 100-240 V socket (17).
•
Connect the other end of the USB Type-C cable (16) to the USB Type-C connector (14) of
the charger.
•
LED indicators (13) will display the battery charge level (see Table).
Note: two batteries can be charged at the same time, a second slot is provided for it.
LED indication (13) in the battery charging mode:
Battery Level
Battery level is from 0% to 25%
Battery level is from 26% to 50%
Battery level is from 51% to 80%
Battery level is from 81% to 99%
The battery is fully charged. It can be
disconnected from the charger.
Defective battery. It is forbidden to
use the battery.
LED indication (13) in the standby mode*:
Battery Level
Battery level is from 0% to 25%
Battery level is from 26% to 50%
Battery level is from 51% to 80%
Battery level is from 81% to 99%
The battery is fully charged. It can be
disconnected from the charger.
Defective battery. It is forbidden to use
the battery.
* Standby mode – operating mode when the batteries in the charger, but the power adapter is not connected.
In this mode, the indication is on for 10 seconds.
Attention! When using a power adapter that does not support USB Power Delivery fast charging technology, the
flicker frequency of LED indicators decreases by 3 times and charge time increases.
Attention! The charger heats up during fast charging. Excess heat is removed through the radiator and does not
affect the device operation.
4