Optional Accessories - Stanley SXH1530 Manual De Instrucciones

Ocultar thumbs

Contenido

página de 15

/ 15
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

ENGLISH (

Original Instructions)

OPERATING INSTRUCTIONS

Installing and removing the battery pack from the tool.

CAUTION! Heating sockets are available in different

diameters! Always use the correct heating socket according

to the intended use! Observe the technical re quirements of

this product (see section "Technical specifications") when

purchasing and using heating sockets!

Note: Socket becomes hot during use! Wear protec-

tive gloves during using in order to avoid injuries like

burns!

Heating Sockets (FIG. B)

Installation

♦ Put the machine on stand (5).

♦ Align heating sockets (6) on both sides of heating

element (4). Screw the heating sockets (6) clockwise on

the heating element (4).

♦ Fix the heating sockets (6) with screw (9), tighten it by

clockwise.

Removing/Placing

♦ Loosen the screw (9) with the wrench (7), remove the

heating sockets (6), if change to another pair of heating

sockets (6), repeat the mentioned above steps.

Thermostat Knob (FIG. C)

WARNING! Make sure the thermostat knob (2) is in its

"0" position and disconnect it from power supply before

making any adjustments.

♦ Turn the thermostat knob (2) clockwise (as seen from

operators position) to increase the temperature.

♦ Turn the thermostat knob (2) anticlockwise (as seen

from operators position) to decrease the temperature.

Indicator

♦ When power on, the thermostat knob (2) to its "0"

position, the green indicator turned on.

♦ Turn the themostat knob (2) clockwise (as seen from

operators position) to increase the temperature, the red

indicator turned on.

♦ After reached to required temperature, the red indicator

turned off, and the green indicator turned on.

Welding (Fig. D, Fig. E)

♦ Put the assembled machine on flat mesa.

♦ Turn the thermostat knob (2) to required temperature.

♦ When red indicator turn off, push the pipe and connector

into corresponding matrixes and keeping some time.

♦ Pull the pipe and connector out and insert to each other

in seconds until it cool down.

♦ Turn the thermostat knob (2) to its "0" position. Let

the heating socket (6) cool down before lifting it from

heating element (4).

MAINTENANCE

Your Stanley tool has been designed to operate over a long

period of time with a minimum of maintenance. continuous

satisfactory operation depends upon proper tool care and

regular cleaning.

WARNING! To minimize the danger of serious

personal injury, please switch off the tool power and

disconnect all plugs before adjusting or removing/

installing any accessory. Before reassembling the tool,

press and release the trigger switch to make sure the tool is

already switched off.

WARNING! Before performing any maintenance on corded/

cordless power tools:

Lubrication

Stanley tools are properly lubricated at the factory

and are ready for use.

Tools should be lubricated regularly every year depending

on usage. (Tools used on heavy duty jobs and tools

exposed to heat may require more frequent lubrication.)

This lubrication should be attempted only by trained power

tool repairperson's such as those at Stanley service centers

or in other qualified service personnel.

Cleaning

WARNING! Regularly clean the ventilation

slots in your tool using a soft brush or dry

cloth.

WARNING! Never use solvents or harsh

chemicals to clean non-metal parts of the

tool. These chemicals may weaken the

material of the parts. Use only mild soap

and damp cloth to clean the tool. Never let

any liquid get inside the tool; never immerse

any part of the tool into liquid.

¡IMPORTANT! To ensure product SAFETY

and RELIABILITY, repairs, maintenance

and adjustment (other than those listed in

this manual) should be performed by

authorized service centers or other qualified

organizations,

replacement parts. Unit contains no user

service able parts inside.