Electrical Safety; Safety Of Others - Stanley SXH1530 Manual De Instrucciones

ENGLISH (
Original Instructions)
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
ADDITIONAL POWER TOOL SAFETY WARNINGS
WARNING! Additional safety warnings for drills and drill/
drivers.
♦ Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
♦ Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
♦ Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "Live" wire may make exposed
metal parts of the power tool "Live" and could give the
operator an electric shock.
♦ Hold power tool by insulated gripping surfaces
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"Live" wire may make exposed metal parts of the power
tool "Live" and could give the operator an electric shock.
♦ Use clamps or another practical way to secure
and support the work piece to a stable platform.
Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
♦ Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
♦ Avoid touching the tip of a drill bit just after
drilling, as it may be hot.
♦ This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance. The intended
use is described in this instruction manual. The use of
any accessory or attachment or performance of any
operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.

ELECTRICAL SAFETY

♦ The device may only be connected to a socket that is
correctly installed and grounded.
♦ The fuse must be a residual current circuit-breaker with
a measured residual current of no more than 30 mA.
♦ Read and observe the instructions for use before using
for the first time.
♦ Make sure that the power supply corresponds with
the connection specifications of the device before it is
connected.
10
♦ The tool may only be used within the specified
limitations for voltage and power (see type plate).
♦ Do not touch the mains plug with wet hands! Always
pull out the mains plug at the plug and not by the cable.
♦ Do not bend, crush, pull or drive over the power cable,
protect from sharp edges,oil and heat.
♦ Do not lift the device using the cable or use the cable for
purposes other than intended.
♦ Check the plug and cable before each use.
♦ If the power cable is damaged immediately disconnect
the plug. Never use the device if the power cable is
damaged.
♦ If the device is not in use make sure the plug is pulled
out.
♦ Make sure that the device is switched off before
plugging in the mains cable.
♦ Make sure that the device is switched off before
unplugging it.
♦ Disconnect the power supply before transporting the
device.

SAFETY OF OTHERS

♦ This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
♦ Children should be supervised to ensure that they do
not play with the appliance.
DEVICE-SPECIFIC SAFETY INSTRUCTIONS
♦ Make sure the workplace is adequately ventilated.
Residual gases and vapours can be harmful to health.
♦ Do not operate the product in moist environments or
allow it to become moist.
♦ Careless handling of the product increases the risk of
fire and explosion.
♦ Flammable and toxic gases can develop when working
with synthetics, paints, varnishes and similar materials.
Do not work in the proximity of highly flammable gases
or materials.
♦ Heat can reach flammable parts that are not visible.
♦ Do not use the product in the same position for a long
time.
♦ Never point the hot air current at persons or animals.
♦ Never use the product as a hair dryer or for drying
clothing.
♦ Do not move the heating element too close to the part
to be treated. The resultant build up of air can cause the
product to overheat.
♦ Do not block the air inlet openings.
♦ Let the product completely cool before storing. The
heating element can cause damage and fires.
♦ Symbols affixed to your tools may not be removed or
covered. Information on the device that is no longer
legible must be replaced immediately.